My Account
Blast Nozzles
Showing 16–30 of 34 results
-
Short nozzles with straight bore are made for close-range spot blasting. The blast pattern is small, making it ideal for cleaning small areas, railings, etc. Other details as follows:- Fine thread, 1-¼" - 11-½" NPSM
- Available in sizes from #3 to #8
- Tungsten carbide liner
-
Short venturi nozzles are made for close-range blasting. The venturi allows the widest possible pattern in limited space environments. Other details as follows:
- Available in either Contractor thread (50mm) or Fine thread (1-¼")
- Available in orifice sizes from #3 to #12
- Tungsten carbide liner
- Multiple jacket types available
-
Refresh your Tite Space Invader Blasting Kit with replacement repair rods. Comes in various lengths from 12 - 60 inches.
- Durable and long-lasting construction
- Easy-to-use design for quick repairs
- Compatible with a variety of pipe sizes and materials
-
BNWBHPAdapts a contractor thread nozzle to a wet blasting nozzle. More control than with a halo nozzle.
- Injects water internally into the abrasive / air stream
- Adapter connects to the nozzle holder, and holds a contractor thread nozzle.
- Includes needle valve to optimize mixture
- Requires a pressure washer to operate, set for 500-1000 psi, 2-4 GPM flow
BNWBHPAdapts a contractor thread nozzle to a wet blasting nozzle. More control than with a halo nozzle.- Injects water internally into the abrasive / air stream
- Adapter connects to the nozzle holder, and holds a contractor thread nozzle.
- Includes needle valve to optimize mixture
- Requires a pressure washer to operate, set for 500-1000 psi, 2-4 GPM flow
-
These medium thread nozzles have a longer venturi than the BNAT nozzle series, making them ideal for use in our RotorBlast internal pipe blaster (when blasting pipe 12" in diamater or greater). Available in multiple orifice sizes. When using them in pairs (like when using in the RotorBlast), be sure to calculate your compressor CFM size requirement accordingly.
-
Tite-Space nozzles are angle nozzles, designed for use in areas that are especially difficult to access, and feature:
- 3/8" NPT Thread in either Male or Female configuration
- Male version has brass threads and requires a minimum opening clearance of 1". This version is 1-7/8" long.
- Female version has steel threads and requires a minimum opening clearance of only ¾". This version is 3-1/8" long.
- These nozzles are often used in conjunction with our Tite Space Invader Blasting Kit, available here
- Angle options include:
- 45° & 60° forward blast
- 90° right angle blast
- 135° reverse blast
- Some options available in double, triple or quad orifices in addition to single.
- Note: Using nozzles with multiple orifices will multiply the compressed air CFM requirement accordingly.
- Stock version uses tungsten carbide lining.
-
- 2" UNC (50mm) coarse Contractor thread 'C' or 1 1/4" NPSM (32mm) Fine Industrial thread 'F'
- Square thorat entry, venturi
- Tungsten carbide liner
- Urethane jacket, brass thread
- Large square blast pattern - less overlap when blasting
- Alignment ridges on jacket
-
Sized between the Tite Space and the full size nozzles, the ATA series of angle nozzles come standard with ¾" Medium Threads. They are excellent for applications requiring the operator to operate in small areas, especially when paired with a small bore whip-hose. Basic specs are:
- 3/4" (20mm) Medium male thread (other options available by special order). Can be used in standard Fine or Coarse nozzle holders by use of a thread adapter available here.
- 1/2" (13mm) throat entry
- 45° forward, 90° right angle, and 135° reverse blast pattern options available
- Some sizes are available in Double, Triple or Quad orifices
- Note: Using nozzles with multiple orifices will multiply the compressed air CFM requirement accordingly
- Tungsten carbide liner. Extended life liners for large projects available by special order.
- Short 2-1/8" length
-
BNATC360COffers Quick and Easy Setup for blast cleaning on internals of small pipes
- Blasts in a 360 degree pattern
- Can be used in pipes from 2.5 to 5 inch ID
- Machined aluminum jacket with tungsten carbide liner
- Replaceable tungsten carbide deflector tip
- Coarse, 2" Contractor Thread
- Screws directly into nozzle holder
- NOTE - requires Nylon nozzle holder with contractor threads
BNATC360COffers Quick and Easy Setup for blast cleaning on internals of small pipes- Blasts in a 360 degree pattern
- Can be used in pipes from 2.5 to 5 inch ID
- Machined aluminum jacket with tungsten carbide liner
- Replaceable tungsten carbide deflector tip
- Coarse, 2" Contractor Thread
- Screws directly into nozzle holder
- NOTE - requires Nylon nozzle holder with contractor threads
-
- 3/4" NPSM (20mm) 'M' Medium thread
- 1/2" (13mm) throat entry
- Tungsten carbide liner
- Aluminum jacket and thread
- Very short - 1-5/8" long
- Commonly used with Internal Pipe RotorBlast when blasting pipes between 8 and 11 inches in diameter, or in other hard-to-reach blasting areas
- Uses HFGFBSP nozzle washers (not included) - order separately
-
FAN BLAST™ Fan Pattern SiALON Blast Nozzles give wide, even blast patterns, ideal for sweep blasting. Different variations include:
- 2" UNC (50mm) coarse contractor thread
- 1-1/4" ( N.P.S.M.) fine industrial thread
-
BNATLW3C
- 2" UNC (50 mm) coarse Contractor thread
- 1 1/4" (32 mm) wide throat entry, long venturi
- Tungsten carbide liner
- 'The Original' Contractor favorite
- Standard weight aluminum jacket and thread
- Use HF G32P nozzle washes (not included - order separately)
BNATLW3C- 2" UNC (50 mm) coarse Contractor thread
- 1 1/4" (32 mm) wide throat entry, long venturi
- Tungsten carbide liner
- 'The Original' Contractor favorite
- Standard weight aluminum jacket and thread
- Use HF G32P nozzle washes (not included - order separately)
-
- Ideal for blasting recesses, pipe internals, behind angles, lattices etc.
- 2" UNC (50mm) coarse Contractor thread 'C' or 1 1/4" NPSM (32mm) Fine Industrial thread 'F'
- 3/4" (20mm) throat entry
- 45° single, double or triple (equi-spaced) side outlets
- Tungsten carbide liner
- **Triple orifice nozzles have triple air & abrasive consumption!
-
- Suits 1 1/4" blast hose
- Durable steel jacket
-
INH131PBAGThe “Blast Nozzle Wear Size Analyzer Gauge” (SKU: INH131PBAG) efficiently determines the internal diameter and wear level of a blast nozzle orifice, ensuring optimal blasting performance.
- Used to determine the internal diameter of a blast nozzle orifice
- Allows you to determine the level of wear of the blast nozzle
- Comes with a removable cap and crayon
- Has size markings to allow you to see quickly what size your nozzle is
- Sold Individually
INH131PBAGThe “Blast Nozzle Wear Size Analyzer Gauge” (SKU: INH131PBAG) efficiently determines the internal diameter and wear level of a blast nozzle orifice, ensuring optimal blasting performance.- Used to determine the internal diameter of a blast nozzle orifice
- Allows you to determine the level of wear of the blast nozzle
- Comes with a removable cap and crayon
- Has size markings to allow you to see quickly what size your nozzle is
- Sold Individually
Part Number Purchase Price INH131PBAG $75.00 Web price iPlease sign in to your account to see your pricing, which may be different from the price displayed.$75.00
-
