Inspection
Showing 31–45 of 152 results
-
Thickness Standards are used to verify the accuracy and operation of coating thickness gauges. As a component of ISO 9000 or in-house quality control procedures, they are a practical alternative to sending instruments to DeFelsko for calibration. These Plastic Shims (aka foils) are low-cost alternative to coated metal plates. They are available in Certified (individual shims or full sets) and in Un-Certified sets. Accuracy is somewhat less than metal plates and they are more sensitive to heat. They are intended for use over a Zero Plate, or over an uncoated substrate. A set of un-certified plastic shims is included with most electronic DeFelsko coating thickness gauges. Replacement sets and certified options are available here as follows:
- Un-Certified. These are checked for accuracy within tolerance shown below at DeFelsko, but are not traceable to any standard. They come as a set of 5 only, in the following approximate thicknesses:
- 25 microns / 1 mil (Orange), +- 20% accuracy
- 50 microns / 2 mils (Red), +- 10% accuracy
- 125 microns / 5 mils (Blue), +- 5% accuracy
- 250 microns / 10 mils (Brown), +- 5% accuracy
- 500 microns / 20 mils (Yellow), +- 5% accuracy
- Certified. Includes certificate of calibration traceable to PTB and all are accurate to within 2 microns / 0.08 mils. Available in the following thicknesses individually, or as a complete set of 8 shims:
- 25 microns / 1 mil (Orange)
- 50 microns / 2 mils (Red)
- 75 microns / 3 mils (Green)
- 125 microns / 5 mils (Blue)
- 250 microns / 10 mils (Brown)
- 500 microns / 20 mils (Yellow)
- 1000 microns / 40 mils (White)
- 1500 microns / 60 mils (Black)
- Un-Certified. These are checked for accuracy within tolerance shown below at DeFelsko, but are not traceable to any standard. They come as a set of 5 only, in the following approximate thicknesses:
-
The PosiTector® CMM IS - DeFelsko's solution for In Situ Concrete Moisture Metering conforming to ASTM F2170 testing standards. Innovative and simple to use, this PosiTector Concrete Moisture Meter offers the highest levels of testing accuracy, helping to prevent costly concrete coating failures. Selected features as follows:
- Simple Design. Individual In-Situ meters, inserted into holes drilled into concrete, connect wirelessly to the PosiTector App, or to a PosiTector Advanced Gage/DPM probe.
- Capable. The PosiTector CMMIS offers the most accurate moisture measurement in concrete as it detects moisture levels well below the floor surface.
- Configurable. With various expandable package options, the CMM IS platform can test on any size concrete floor, as follows:
- 3 probe Basic Kit, including caps, probe sleeve extensions, calibration check chambers and other accessories required for testing.
- 5 probe Complete Kit, including all the above plus a carrying case and a vacuum tool for cleaning out the drilled holes.
- 5 Probe Pro Kit, combines a PosiTector Advanced Gage/DPM probe with the above Complete Kit.
-
The PosiTector® DPM - DeFelsko's solution for measurement of climatic conditions for industrial coating applications. Versatile and capable, these environmental measuring instruments have the following highlights:
- Familiar. Built on the tried-and-true PosiTector® gauge/body platform design with interchangeable probes.
- Capable. Measures and records environmental conditions including:
- Relative Humidity (RH)
- Air Temperature
- Surface Temperature
- Dew Point temperature
- Surface/Dew Point Delta
- Wind speed (one model only)
- Wet-Bulb (when used with Advanced Bodies only)
- Configurable. Available as probes-only (to use with an existing gage/body), or in packages with a new gage body, these DPM probes are available as:
- DPM Integral, with direct-contact surface thermometer
- DPMIR Integral, with infrared surface thermometer, for use on moving parts, very hot parts, etc., where direct contact is not possible.
- DPMS Integral, with cabled, magnetic surface temperature sensor for continuously logging surface temperatures. Also available for this model are 2 options:
- A liquid temperature probe, for measuring paint temperature prior to application
- A hand-held surface temperature probe, for spot-checking hard-to-reach areas.
- DPMA Integral, with all standard features plus a wind-speed indicator
- DPMD Cabled, with ½" NPT threads for insertion into pipe and other areas that can't be accessed by other versions.
Note: The PosiTector® DPM L is an autonomous version, and can be attached independently to steel for longer-term climatic condition recording. See you may also like below.
-
The PosiTector GLS - DeFelsko's system for measuring glossiness, haze, and more. Working on many varied substrates, the DeFelsko GLS gloss meter is highly capable with the following highlights:
- Familiar. The GLS probe is built on the tried-and-true PosiTector gage/body platform as one of many interchangeable measurement probes.
- Capable. Three separate probe designs available for the following applications:
- 60° measurement angle, suitable for most gloss applications and the preferred angle for semi-gloss
- Combination 20°/60° measurement angles, suitable for high and semi-gloss applications w/haze indexing.
- Combination 20°/60°/85° measurement angles, suitable for matte, high-, and semi-gloss applications, also with haze indexing.
- Configurable. Available as follows:
- Probe only. Use with your existing PosiTector gauge.
- Standard PosiTector package with choice of probe.
- Advanced PosiTector package with choice of probe.
- Note: All PosiTector GLS packages come with case, integrated calibration standard, calibration certificate, and more.
-
The PosiTector IRT - DeFelsko's solution for dedicated, non-contact temperature measurement. It is rich in features, as follows:
- Familiar. Built on the tried-and-true PosiTector® platform with the interchangeable probe design.
- Capable. Works where conventional sensors cannot, it measures surface temperatures on moving parts, hard-to-reach areas, and objects whose temperatures are higher than the range of direct-contact sensors.
- Economical. When measurement of other climatic conditions is not required, this PosiTector IRT saves money vs. the higher-featured PosiTector DPM IR.
- Configurable. Available as follows:
- Probe-only (use with existing gauge / body)
- Package with Standard gauge / body
- Package with Advanced gauge / body
-
The PosiTector®SHD - DeFelsko's solution for measuring shore hardness on non-metallic surfaces. Capable and configurable, it offers the following:
- Familiar. Built on the tried-and-true PosiTector gauge / body platform, with interchangeable measurement probe options.
- Capable. The SHD comes in two probe models for different hardness ranges.
- Shore A (soft to hard materials such as soft rubber, elastomers, neoprene, silicone, etc.
- Shore D (medium to extra hard materials such as hard rubber, hard plastics, epoxies, PVC, acrylic, etc.
- Configurable. Available as follows:
- Probe only. Use with your existing PosiTector gage.
- Standard PosiTector package with choice of probe.
- Advanced PosiTector package with choice of probe.
- Note: All PosiTector SHD packages come with case, test block, calibration certificate, holster, and more.
-
PosiTector SHD Test Blocks - DeFelsko accessories for checking the operation of the SHD Durometer Probes. Available in 3 variations each for Shore A and Shore D hardness measurement ranges.
-
DeFelsko test stands for use with their Shore Hardness Durometers: Helps reduce operator influence on testing results by positioning the probe in a controlled, repeatable way. Two types available:
- INDSHDSTANDA - for use with Shore A probe. 1 kg (2.2 lb) deadweight included.
- INDSHDSTANDD - for use with a Shore D probe. 5 kg (11 lb) deadweight included.
-
INDSHDPRBMNTUsing a testing stand is the preferred way to reduce operator influence on the test results when using a SHD probe. For applications where customers already have a test stand from a different manufacturer, this threaded universal mount can be used as an adaptor for the DeFelsko SHD test probe, at a lower cost than the full DeFelsko test stand assembly.INDSHDPRBMNTUsing a testing stand is the preferred way to reduce operator influence on the test results when using a SHD probe. For applications where customers already have a test stand from a different manufacturer, this threaded universal mount can be used as an adaptor for the DeFelsko SHD test probe, at a lower cost than the full DeFelsko test stand assembly.
-
The PosiTector® SPG - DeFelsko's solution for measuring surface profiles on both metal and concrete surfaces - without the need of Testex® tape. This inspection instrument system is capable and configurable, and has the following highlights:
- Familiar. Built on the tried-and-true PosiTector gauge / body platform, using interchangeable probes.
- Capable. Five separate probe designs available as follows:
- PRBSPG. Integral probe for one-handed use. Measures flat blasted steel.
- PRBSPGS. Cabled probe for enhanced ergonomics and/or access to hard-to-reach areas. Measures flat blasted steel.
- PRBSPGOS. Cabled probe for use on convex curved blasted steel (especially pipes).
- PRBSPGCS. Cabled probe for measuring textured coatings and other surface profile applications.
- PRBSPGTS. Cabled probe for measuring concrete profile.
- Configurable. Available as follows:
- Probe only. Use with your existing PosiTector gauge.
- Standard PosiTector body package with choice of probe.
- Advanced PosiTector body package with choice of probe.
- Note: All PosiTector SPG packages come with case, zero plate / shim, calibration certificate, and more.
-
The PosiTector UTG - DeFelsko's solution for measurement of wall thicknesses of pipes, tanks, and more where access is limited to one side. Here are some highlights of the highly capable DeFelsko ultrasonic thickness gage probe family:
- Familiar. The UTG family of probes are interchangeable with the tried-and-true DeFelsko gage body platform.
- Capable. Six different probe versions are available, depending on the requirements of the application. The first four are standard corrosion single-echo probes designed for applications where the surface is unpainted (or has the paint removed.)
- PRBUTGC: Standard frequency 5mz transducer. Cabled.
- PRBUTGCX: Xtreme version of above with a braided stainless cable with strain relief for demanding use.
- PRBUTGCA: Same as above, except integral non-cabled design. This version is ideal for one-handed use.
- PRBUTGCLF. Low-frequency 2.25mz transducer for attenuative materials like cast iron. Standard cable.
- The following two models are both cabled, and can be used on either painted or non-painted substrates.
- PRBUTGM: 5mz transducer with highly versatile single and multi-echo modes. Single mode offers greater (up to 5 inches thick) measurement range, but should be used where paint has been removed. Multi-echo mode does not require the paint to be removed and can measure walls up to 2.5 inches thick. This version has a durable alumina wear face and is ideal for use on rough or blasted surfaces.
- PRBUTGP: 15mz transducer offers high precision when measuring thin materials (up to .475 inch thick steel or up to .175 inch thick plastic). It has automatic single / multi echo mode switching for use on painted or unpainted surfaces. This probe can be used to measure thicknesses of plastic bottles, aircraft windows, thin-wall pipe, and much more.
- Configurable. Any of the six probes can be configured in the following packages:
- Probe only. Use with your existing PosiTector gauge.
- Standard PosiTector package with choice of probe.
- Advanced PosiTector package with choice of probe.
- Note: All PosiTector UTG packages come with case, ultrasonic gel, calibration certificate, and more.