My Account
Blast Nozzles
Silenced / Quiet Nozzles
Angled Blast Nozzles
General Purpose Nozzles
High Performance Nozzles
Internal Pipe (ID) Nozzles
Short / Compact Nozzles
Tools & Nozzle Thread Adapters
Wet-Blast, Specialty & Other Nozzles
Showing 16–30 of 46 results
-
Effective solution for blasting in hard-to-reach areas such as:- Inside of bolt holes
- Inside of close-fitting steel channels
- Difficult access structural steel, such as bridge supports, etc.
- Offers standard extension lengths from 10 to 60 inches, with other options available by special order.
- Can be used with most abrasives
- Attaches to blast hoses with standard 2-prong couplings (not nozzle holders)
- Nozzle is NOT included and shown for illustration purposes only. Requires junior size 3/8" NPT threaded nozzles. Choose the correct one for your application from our Tite-Space nozzle selection here.
- Female version requires only ¾" clearance.
- Male version requires only 1" clearance.
-
Short nozzles with straight bore are made for close-range spot blasting. The blast pattern is small, making it ideal for cleaning small areas, railings, etc. Other details as follows:- Fine thread, 1-¼" - 11-½" NPSM
- Available in sizes from #3 to #8
- Tungsten carbide liner
-
Short venturi nozzles are made for close-range blasting. The venturi allows the widest possible pattern in limited space environments. Other details as follows:- Available in either Contractor thread (50mm) or Fine thread (1-¼")
- Available in orifice sizes from #3 to #12
- Tungsten carbide liner
- Multiple jacket types available
-
Refresh your Tite Space Invader Blasting Kit with replacement repair rods. Comes in various lengths from 12 - 60 inches.
- Durable and long-lasting construction
- 3/8" Schedule 40, NPT threaded on both ends
- Use with Tite-Space Invaders or with Junior size internal pipe blasters
-
Tite-Space nozzles are angle nozzles, designed for use in areas that are especially difficult to access, and feature:
- 3/8" NPT Thread in either Male or Female configuration
- Male version has brass threads and requires a minimum opening clearance of 1". This version is 1-7/8" long.
- Female version has steel threads and requires a minimum opening clearance of only ¾". This version is 3-1/8" long.
- These nozzles are often used in conjunction with our Tite Space Invader Blasting Kit, available here
- Angle options include:
- 45° & 60° forward blast
- 90° right angle blast
- 135° reverse blast
- Some options available in double, triple or quad orifices in addition to single.
- Note: Using nozzles with multiple orifices will multiply the compressed air CFM requirement accordingly.
- Stock version uses tungsten carbide lining.
-
BNWBHPAdapts a contractor thread nozzle to a wet blasting nozzle. More control than with a halo nozzle.
- Injects water internally into the abrasive / air stream
- Adapter connects to the nozzle holder, and holds a contractor thread nozzle.
- Includes needle valve to optimize mixture
- Requires a pressure washer to operate, set for 500-1000 psi, 2-4 GPM flow
BNWBHPAdapts a contractor thread nozzle to a wet blasting nozzle. More control than with a halo nozzle.- Injects water internally into the abrasive / air stream
- Adapter connects to the nozzle holder, and holds a contractor thread nozzle.
- Includes needle valve to optimize mixture
- Requires a pressure washer to operate, set for 500-1000 psi, 2-4 GPM flow
-
BAHNGKit
The “Blast Nozzle Pressure Test Kit” (SKU: BAHNGKit) by BlastOne ensures quick and accurate nozzle pressure testing. Comes complete with a stainless steel pressure gage, needles, and a protective leather-bound case.
- For testing air pressure at the nozzle
- Uses hyperdermic needles which insert into the blast hose to take the nozzle pressure
- Insert about 6-10ft behind blaster for most accurate reading
- Test kit includes:
- Liquid filled stainless steel pressure gage with dual pressure & efficiency scale
- Four needles and instructions
- Protective leather bound case
- Sold as a Kit
- MPN 2010-014-03
Note - there is no calibration certificate process available for this item.
BAHNGKitThe “Blast Nozzle Pressure Test Kit” (SKU: BAHNGKit) by BlastOne ensures quick and accurate nozzle pressure testing. Comes complete with a stainless steel pressure gage, needles, and a protective leather-bound case.
- For testing air pressure at the nozzle
- Uses hyperdermic needles which insert into the blast hose to take the nozzle pressure
- Insert about 6-10ft behind blaster for most accurate reading
- Test kit includes:
- Liquid filled stainless steel pressure gage with dual pressure & efficiency scale
- Four needles and instructions
- Protective leather bound case
- Sold as a Kit
- MPN 2010-014-03
Note - there is no calibration certificate process available for this item.
-
VCBV066
- Suits Blast and Vac Workhead VCBV100 (Wheeled Unit)
- Nozzle Internal Venturi 3/8" #6 Long Venturi
- Long Lasting
- Sold Individually
VCBV066- Suits Blast and Vac Workhead VCBV100 (Wheeled Unit)
- Nozzle Internal Venturi 3/8" #6 Long Venturi
- Long Lasting
- Sold Individually
-
- Used for blasting pipe internals with 3"-12" ID
- Blasts in a 360 degree pattern
- Units come standard with Tungsten Carbide deflector tip
- Select the unit that will best match your Air Supply:
- IPC4000, 1/2" Throat Nozzle: 250 cfm
- IPC4500, 5/8" Throat Nozzle: 400 cfm
- Order Transport Carriages separately as follows:
- IPC4100, Collar and Button, for 3"-5" ID
- IPC4200, Scissor, for 5"-12" ID
- Requires BSP (not NPT) threaded coupling to attached to standard blast hose coupling, part number HFSTC1BSP, available here or under the repair parts tab below.
- Successful Internal Pipe Projects require some specialist knowledge - contact our team for assistance
- Note: This product is similar to the Clemco Hollo-Blast
-
These medium thread nozzles have a longer venturi than the BNAT nozzle series, making them ideal for use in our RotorBlast internal pipe blaster (when blasting pipe 12" in diamater or greater). Available in multiple orifice sizes. When using them in pairs (like when using in the RotorBlast), be sure to calculate your compressor CFM size requirement accordingly.
-
VCBV104
- Suits Blast and Vac Workhead BNV-3/VCBV200 (Standard Unit)
- Nozzle Internal Venturi 1/4" #4 Long Venturi
- Long Lasting
- Sold Individually
VCBV104- Suits Blast and Vac Workhead BNV-3/VCBV200 (Standard Unit)
- Nozzle Internal Venturi 1/4" #4 Long Venturi
- Long Lasting
- Sold Individually
-
VC803300010BlastOne has the parts needed for your MiniBRS Trigger Workheads. This is the #4 Nozzle (8033-000-10) for both the pneumatic and electric versions.VC803300010BlastOne has the parts needed for your MiniBRS Trigger Workheads. This is the #4 Nozzle (8033-000-10) for both the pneumatic and electric versions.
Part Number Purchase Price VC803300010 $350.00 Web price iPlease sign in to your account to see your pricing, which may be different from the price displayed.$350.00
-
-
VC803300009BlastOne has the parts needed for your MiniBRS G2 Trigger Workheads. This is the #3 Blast Nozzle (8033-000-09) for both the pneumatic and electric version.VC803300009BlastOne has the parts needed for your MiniBRS G2 Trigger Workheads. This is the #3 Blast Nozzle (8033-000-09) for both the pneumatic and electric version.
Part Number Purchase Price VC803300009 $355.83 Web price iPlease sign in to your account to see your pricing, which may be different from the price displayed.$355.83
-
-
- 2" UNC (50mm) coarse Contractor thread 'C' or 1 1/4" NPSM (32mm) Fine Industrial thread 'F'
- Square thorat entry, venturi
- Tungsten carbide liner
- Urethane jacket, brass thread
- Large square blast pattern - less overlap when blasting
- Alignment ridges on jacket
-
Sized between the Tite Space and the full size nozzles, the ATA series of angle nozzles come standard with ¾" Medium Threads. They are excellent for applications requiring the operator to operate in small areas, especially when paired with a small bore whip-hose. Basic specs are:
- 3/4" (20mm) Medium male thread (other options available by special order). Can be used in standard Fine or Coarse nozzle holders by use of a thread adapter available here.
- 1/2" (13mm) throat entry
- 45° forward, 90° right angle, and 135° reverse blast pattern options available
- Some sizes are available in Double, Triple or Quad orifices
- Note: Using nozzles with multiple orifices will multiply the compressed air CFM requirement accordingly
- Tungsten carbide liner. Extended life liners for large projects available by special order.
- Short 2-1/8" length
