Blast Equipment Parts
Showing 121–135 of 351 results
-
When your G3 Trigger Deadman system needs refreshed, we have the replacement parts you need. These are the replacement trigger subassemblies.
- Easy to install
- Offered in 4 variations
-
KA018
- Toggle Actuator for Pneumatic Remote Abrasive Cut-Off
- 1/8"
KA018- Toggle Actuator for Pneumatic Remote Abrasive Cut-Off
- 1/8"
-
BA01998BlastOne has the parts to maintain your Clemco® blast equipment. This is the replacement plug washer retainer for the remote control valve (factory number 01998).BA01998BlastOne has the parts to maintain your Clemco® blast equipment. This is the replacement plug washer retainer for the remote control valve (factory number 01998).
-
- European-style remote controls
- 1-1/4" (32mm) thread inlet valve
- 3/4" (19mm) thread ported exhaust valve
- Available as an integrated inlet/exhaust assembly
- Supplied standard as separate valves for simplified installation and ease of maintenance
- Service repair kit includes seals, gaskets, etc. to service both the inlet and exhaust valve
- Optional service kit #2 also includes exhaust deflector plate and gasket
- Recommended replacement is the Combo Valve System- DM2223RK00
-
DMPYT400
- Piston-operated valve
- 1/4" female NPT supply air connection
- Effortless activation via deadman control handle
- Guide tubes ensure consistent plunger travel
- Eliminate repressurization down time profit loss
DMPYT400- Piston-operated valve
- 1/4" female NPT supply air connection
- Effortless activation via deadman control handle
- Guide tubes ensure consistent plunger travel
- Eliminate repressurization down time profit loss
-
DMRGNE2099RGNE Electric Switch with a 300mm CordDMRGNE2099RGNE Electric Switch with a 300mm Cord
-
- Deadman-operated control valve (solenoid). Pneumatic or electric versions available.
- Uses an electric or pneumatic charge to push over the shuttle which opens ports to control the deadman system
- Provides sharp, clean and rapid response
- Improves safety
- Installs between twinline and inlet valve
- Reduces wear on both the remote control exhaust valve and the abrasive metering valve
-
BA02006BlastOne has the parts to maintain your Clemco® blast equipment. This is the replacement bottom cap seal for the remote control inlet valve (factory part number 02006).BA02006BlastOne has the parts to maintain your Clemco® blast equipment. This is the replacement bottom cap seal for the remote control inlet valve (factory part number 02006).
-
DMRMCVEBK
BlastOne has the parts to maintain your Clemco® blast equipment. This is the rebuild kit for the piston outlet valve (factory part number 01928). Includes the following:
- BA01969 Plug Washers (2)
- BA01972 Valve Plug
- BA01974 Compression Spring
- BA01986 Plug Washer Retainer
NOTE: BlastOne also has retrofit kits with upgraded valves, and which are designed to reduce maintenance while keeping your current pot. For pressure hold retrofit kits, see here. For pressure-release retrofit kits, see here.
DMRMCVEBKBlastOne has the parts to maintain your Clemco® blast equipment. This is the rebuild kit for the piston outlet valve (factory part number 01928). Includes the following:
- BA01969 Plug Washers (2)
- BA01972 Valve Plug
- BA01974 Compression Spring
- BA01986 Plug Washer Retainer
NOTE: BlastOne also has retrofit kits with upgraded valves, and which are designed to reduce maintenance while keeping your current pot. For pressure hold retrofit kits, see here. For pressure-release retrofit kits, see here.
-
DMRMCVIBK
BlastOne has the parts to maintain your Clemco® blast equipment. This is the rebuild kit for the 1-½" inlet valve (replaces factory part number 01927). Includes the following:
- BA01982 Compression Spring, small
- BA01998 Plug Washers (2)
- BA02000 Compression Spring, large
- BA02002 Plug Washer Retainer
- BA02006 Bottom Cap Seal
- BA02007 O-Ring, large
- BA02008 O-Ring, small
If you need the rebuild kit for the 1" inlet valve version, click here.
NOTE: BlastOne also has retrofit kits with upgraded valves, and which are designed to reduce maintenance while keeping your current pot. For pressure hold retrofit kits, see here. For pressure-release kits, see here.
DMRMCVIBKBlastOne has the parts to maintain your Clemco® blast equipment. This is the rebuild kit for the 1-½" inlet valve (replaces factory part number 01927). Includes the following:
- BA01982 Compression Spring, small
- BA01998 Plug Washers (2)
- BA02000 Compression Spring, large
- BA02002 Plug Washer Retainer
- BA02006 Bottom Cap Seal
- BA02007 O-Ring, large
- BA02008 O-Ring, small
If you need the rebuild kit for the 1" inlet valve version, click here.
NOTE: BlastOne also has retrofit kits with upgraded valves, and which are designed to reduce maintenance while keeping your current pot. For pressure hold retrofit kits, see here. For pressure-release kits, see here.
-
-
BA02002BlastOne has the parts to maintain your Clemco® blast equipment. This is the replacement plug washer retainer for the remote control valve (factory part number 02002).BA02002BlastOne has the parts to maintain your Clemco® blast equipment. This is the replacement plug washer retainer for the remote control valve (factory part number 02002).
-
GV2410320SPBV
- Tri-Clover Connector with Built in Ball-Valve
- Locate between the metering valve and the bottom of the pot to reduce maintenance time on the metering valve.
- Combines 2 time savers:
- Tri-Clover connection allows for easy removal of metering valve.
- Ball valve allows for removal of metering valve without emptying the pot.
- 1 1/4" x 1 1/4" NPT Threads - suits most blast pots and abrasive metering valves
- Use thread sealant tape or compound to ensure an airtight connection
- NOTE - this option adds 6 inches in height. Ensure that your pot has the required clearance before ordering, or that you can add the needed height to your existing pot.
GV2410320SPBV- Tri-Clover Connector with Built in Ball-Valve
- Locate between the metering valve and the bottom of the pot to reduce maintenance time on the metering valve.
- Combines 2 time savers:
- Tri-Clover connection allows for easy removal of metering valve.
- Ball valve allows for removal of metering valve without emptying the pot.
- 1 1/4" x 1 1/4" NPT Threads - suits most blast pots and abrasive metering valves
- Use thread sealant tape or compound to ensure an airtight connection
- NOTE - this option adds 6 inches in height. Ensure that your pot has the required clearance before ordering, or that you can add the needed height to your existing pot.
-
BAWF8012
- Suits BlastOne MistBlaster Wet/Dry Blasting System
- Used to filter particles out water entering into the pump
- 1/2" FNPT x 1/2" FNPT fittings
- Clear Bowl Strainer Water Filter with Yellow 80 Mesh Filter
- Sold Individually
- Genuine BlastOne Product
BAWF8012- Suits BlastOne MistBlaster Wet/Dry Blasting System
- Used to filter particles out water entering into the pump
- 1/2" FNPT x 1/2" FNPT fittings
- Clear Bowl Strainer Water Filter with Yellow 80 Mesh Filter
- Sold Individually
- Genuine BlastOne Product
Explore our extensive range of blast equipment parts designed to enhance and maintain your blasting operations. From deadman control systems to high-pressure fittings, we provide everything you need to keep your equipment running smoothly and efficiently. Our selection includes durable components like hex pipe nipples, pop-up valves, and hose fittings, ensuring compatibility and high performance. Trust in our products to deliver reliability and safety across all your blasting projects.