Deadman Parts / Control Systems
Showing 46–60 of 94 results
-
KA018
- Toggle Actuator for Pneumatic Remote Abrasive Cut-Off
- 1/8"
KA018- Toggle Actuator for Pneumatic Remote Abrasive Cut-Off
- 1/8"
-
BA01998BlastOne has the parts to maintain your Clemco® blast equipment. This is the replacement plug washer retainer for the remote control valve (factory number 01998).BA01998BlastOne has the parts to maintain your Clemco® blast equipment. This is the replacement plug washer retainer for the remote control valve (factory number 01998).
-
- European-style remote controls
- 1-1/4" (32mm) thread inlet valve
- 3/4" (19mm) thread ported exhaust valve
- Available as an integrated inlet/exhaust assembly
- Supplied standard as separate valves for simplified installation and ease of maintenance
- Service repair kit includes seals, gaskets, etc. to service both the inlet and exhaust valve
- Optional service kit #2 also includes exhaust deflector plate and gasket
- Recommended replacement is the Combo Valve System- DM2223RK00
-
DMPYT400
- Piston-operated valve
- 1/4" female NPT supply air connection
- Effortless activation via deadman control handle
- Guide tubes ensure consistent plunger travel
- Eliminate repressurization down time profit loss
DMPYT400- Piston-operated valve
- 1/4" female NPT supply air connection
- Effortless activation via deadman control handle
- Guide tubes ensure consistent plunger travel
- Eliminate repressurization down time profit loss
-
DMRGNE2099RGNE Electric Switch with a 300mm CordDMRGNE2099RGNE Electric Switch with a 300mm Cord
-
- Deadman-operated control valve (solenoid). Pneumatic or electric versions available.
- Uses an electric or pneumatic charge to push over the shuttle which opens ports to control the deadman system
- Provides sharp, clean and rapid response
- Improves safety
- Installs between twinline and inlet valve
- Reduces wear on both the remote control exhaust valve and the abrasive metering valve
-
BA02006BlastOne has the parts to maintain your Clemco® blast equipment. This is the replacement bottom cap seal for the remote control inlet valve (factory part number 02006).BA02006BlastOne has the parts to maintain your Clemco® blast equipment. This is the replacement bottom cap seal for the remote control inlet valve (factory part number 02006).
-
DMRMCVEBK
BlastOne has the parts to maintain your Clemco® blast equipment. This is the rebuild kit for the piston outlet valve (factory part number 01928). Includes the following:
- BA01969 Plug Washers (2)
- BA01972 Valve Plug
- BA01974 Compression Spring
- BA01986 Plug Washer Retainer
NOTE: BlastOne also has retrofit kits with upgraded valves, and which are designed to reduce maintenance while keeping your current pot. For pressure hold retrofit kits, see here. For pressure-release retrofit kits, see here.
DMRMCVEBKBlastOne has the parts to maintain your Clemco® blast equipment. This is the rebuild kit for the piston outlet valve (factory part number 01928). Includes the following:
- BA01969 Plug Washers (2)
- BA01972 Valve Plug
- BA01974 Compression Spring
- BA01986 Plug Washer Retainer
NOTE: BlastOne also has retrofit kits with upgraded valves, and which are designed to reduce maintenance while keeping your current pot. For pressure hold retrofit kits, see here. For pressure-release retrofit kits, see here.
-
DMRMCVIBK
BlastOne has the parts to maintain your Clemco® blast equipment. This is the rebuild kit for the 1-½" inlet valve (replaces factory part number 01927). Includes the following:
- BA01982 Compression Spring, small
- BA01998 Plug Washers (2)
- BA02000 Compression Spring, large
- BA02002 Plug Washer Retainer
- BA02006 Bottom Cap Seal
- BA02007 O-Ring, large
- BA02008 O-Ring, small
If you need the rebuild kit for the 1" inlet valve version, click here.
NOTE: BlastOne also has retrofit kits with upgraded valves, and which are designed to reduce maintenance while keeping your current pot. For pressure hold retrofit kits, see here. For pressure-release kits, see here.
DMRMCVIBKBlastOne has the parts to maintain your Clemco® blast equipment. This is the rebuild kit for the 1-½" inlet valve (replaces factory part number 01927). Includes the following:
- BA01982 Compression Spring, small
- BA01998 Plug Washers (2)
- BA02000 Compression Spring, large
- BA02002 Plug Washer Retainer
- BA02006 Bottom Cap Seal
- BA02007 O-Ring, large
- BA02008 O-Ring, small
If you need the rebuild kit for the 1" inlet valve version, click here.
NOTE: BlastOne also has retrofit kits with upgraded valves, and which are designed to reduce maintenance while keeping your current pot. For pressure hold retrofit kits, see here. For pressure-release kits, see here.
-
-
BA02002BlastOne has the parts to maintain your Clemco® blast equipment. This is the replacement plug washer retainer for the remote control valve (factory part number 02002).BA02002BlastOne has the parts to maintain your Clemco® blast equipment. This is the replacement plug washer retainer for the remote control valve (factory part number 02002).
-
DMECKCLIP
- Heavy-Duty Battery Charging Clamps - Bare
- Insulated Vinyl handles for your safety
- 80 Amp capacity, suits 12/24V DC batteries
- 14 to 18 AWG
- Sold as a pair - Black/Red
DMECKCLIP- Heavy-Duty Battery Charging Clamps - Bare
- Insulated Vinyl handles for your safety
- 80 Amp capacity, suits 12/24V DC batteries
- 14 to 18 AWG
- Sold as a pair - Black/Red
-
DMWTX1002KLBALL AND CHAIN SOLD SEPARATELY
- Increases productivity and reduces costs
- Permanently sealed pneumatic switch is protected by abrasion-resistant urethane
DMWTX1002KLBALL AND CHAIN SOLD SEPARATELY- Increases productivity and reduces costs
- Permanently sealed pneumatic switch is protected by abrasion-resistant urethane
-
DM227000015PKWhen your BAABS Deadman system needs refreshed, we have the replacement parts you need. This is a pack of 4 of the thread forming screws used in the handle. Other individual components are also available. See the Repair Parts tab on the main BAABS page here.DM227000015PKWhen your BAABS Deadman system needs refreshed, we have the replacement parts you need. This is a pack of 4 of the thread forming screws used in the handle. Other individual components are also available. See the Repair Parts tab on the main BAABS page here.