Search: profile

• General Purpose abrasive used for Sandblasting
• Angular shape creates a profile on steel
• Mohs Hardness of 6-7
• Bulk Density: 75-100 lbs/ft2
• Less then 0.1% free silica
• Not Recommended for blasting on stainless or aluminum
• Comes in many different grades and packaging sizes
• Non-Recycling
• Meets SSPC-AB 1 Standard
• Sold by the pallet (pallet minimum)
• Abrasive cannot be ordered online at this time

• Multi-Purpose abrasive used for Sandblasting a variety of substrates, especially steel and concrete.
• Angular particle shape creates a profile on steel, with only minimal embedment into the surface.
• Mohs Hardness of 6-7
• Bulk Density: 75-100 lbs/ft2
• Less then 0.1% free silica
• Not Recommended for blasting on stainless or aluminum
• Comes in many different grades and packaging sizes
• Non-Recycling
• QPL Approved and MIL Spec approved abrasives available from select plants
• SSPC AB-1 Approved
• Sold by the pallet (pallet minimum)
• Abrasive cannot be ordered online at this time

From the makers of the Nova Respirators!

• GVS Masks are made from TPE and are hypoallergenic and non-irritating.
• Extremely lightweight and comfortable.
• Each mask includes the initial set of filters installed and is ready-to-use.
• Price shown per-each.  Packed 4 per case, with case discount.
• Multiple filter versions available as follows:
  • OV / P100. Removes Organic Vapors along with P100 filtration. Painters choice!
  • OV / AG / P100. Protects against organic, inorganic, chemical gases, and particulates.
    • Solvents
    • Chlorine and Chlorine Dioxide
    • Hydrogen Chloride and Hydrogen Fluoride
    • Sulphur Dioxide
    • Organic Vapors
  • Multi-Gas. Protects against organic, inorganic, chemical and ammonia based gasses. All acid gases above, plus:
    • Ammonia
    • Formaldehyde
    • Hydrogen Sulfide
    • Methylamine
  • Multi-Gas / P100. Protects against organic, inorganic, chemical and ammonia based gases, and particulates.
  • Keep your respirator fresh with the standard-profile line of GVS replacement filters.
• NIOSH Approved with ANSI Z87+ eye protection
• Goggles are scratch and fog resistant.  Tear-off lenses available separately to keep them clean while spraying.

NOTE – This is the standard-profile series, which has the largest variety of protective filters.  Low-profile Integra Masks (which offer an enhanced field of vision) are also available.

Your regular eyeglasses will not fit under these goggles.  However, GVS makes an Integra Prescription Lens insert to fit inside, which you can give to your optician to have fitted with your prescription.

As with all close-fitting respirators, these are designed to be used where fit-testing is conducted. The GVS Portacount Adaptor is available to facilitate this testing.

Replacement filter cartridges to suit GVS Elipse and Integra Standard-Profile half-masks.

• OV / AG / P100. Protects against organic, inorganic, chemical gases, and particulates.
• OV / P100. Protects against organic gases and particulates.
• Multi-Gas. Protects against organic, inorganic, chemical and ammonia based gases.
• Multi-Gas P100. Protects against organic, inorganic, chemical and ammonia based gases, and particulates.

NOTE – This is the standard-profile series. The low-profile series is available here.

Genuine GVS product.

The PosiTector RTR family of instruments is DeFelsko’s state-of-the-art solution for surface profile measurement and more.  Two different probe models are available and selected features are listed below:

• Familiar.  Based on the award-winning PosiTector instrument body platform, the RTR probes are easy to master and use.
• Capable.  State-of-the-art technology with 2 models as follows:
  • PosiTector RTR H.  This 2D version measures surface profile using Testex tape just like a spring micrometer, but with the following enhancements:
    • Automatically compensates for the thickness of the Testex film backing.
    • Using conventional Testex Coarse or X-Coarse tape, the RTR H calculates linearized measurements automatically, without the complicated averaging process required by analog spring micrometers.
    • Stores readings which can be uploaded to PosiSoft, Mac, and smartphone software for professional reporting.  Of course, you can keep the physical replica tape as well.
    • Ready-to-measure.  No calibration adjustment required for most applications.
  • PosiTector RTR 3D.  This 2D / 3D version offers the same features as the RTR H above, but with these extra features:
    • Creates a 3D image of the profile and calculates Peak Density, Peak Count and more – a total of 14 common 2D and 3D surface parameters.
    • When paired with the Advanced body, the RTR 3D can download high-res .SDF files for further analysis.
    • These 3D surface parameters are proving to be as important (if not more so) than traditional surface profile measurements for predicting coating life.  Future proof your instrument purchase against changing specifications by investing in the highly capable PosiTector RTR 3D!
    • Note:  The PosiTector RTR 3D requires Optical grade Testex tape.
• Configurable.  Your choice of RTR probe is available separately (for use with existing PosiTector gage / body), or can be purchased as a kit with your choice of Standard or Advanced body.

Each PosiTector Body / RTR probe kit comes complete with burnishing tool, cleaning cards, check shim(s), calibration certificate, and more!  The RTR 3D package also includes one roll of X-Coarse optical grade tape.

From the makers of the Nova Respirators!

• GVS Half Masks are made from TPE and are hypoallergenic and non-irritating.
• Extremely lightweight and comfortable.
• Each mask includes the initial set of filters installed and is ready-to-use.
• Price shown per-each.  Packed 10 per case, with case discount
• Multiple filter versions available as follows:
  • Standard P100. These filters will remove up to 99.97% of particulates and contaminants down to 0.3 microns.
  • Standard P100 Starter Kit.  Same as above along with a hard carry case and extra set of filters included.
  • Enhanced P100 w/activated charcoal.  Designed to remove nuisance odors along with P100 filtration.
  • OV / P100.  Removes Organic Vapors along with P100 filtration.  Painters choice!
  • Standard P100 Source Control. Designed for healthcare market and reduces cost and waste as compared to N95 disposable masks.  Side exhaust valves removed.
  • Reuse your respirator over and over again with the low-profile line of GVS replacement filters.
• NIOSH Approved TC-84A-8062.

NOTE – This is the low-profile series.  Standard-profile Elipse Masks (which offers Acid Gas & Multi-Gas filter options) are also available.

As with all close-fitting respirators, these are designed to be used where fit-testing is conducted.  The GVS Portacount Adapter is available to facilitate this testing.

From the makers of the Nova Respirators! 

• GVS Half Masks are made from TPE and are hypoallergenic and non-irritating.
• Extremely lightweight and comfortable.
• Each mask includes the initial set of filters installed and is ready-to-use.
• Price shown per-each.  Packed 8 per case, with case discount.
• Multiple filter versions available as follows:
  • OV / P100. Removes Organic Vapors along with P100 filtration. Painters choice!
  • OV / AG / P100. Protects against organic, inorganic, chemical gases, and particulates.
    • Solvents
    • Chlorine and Chlorine Dioxide
    • Hydrogen Chloride and Hydrogen Fluoride
    • Sulphur Dioxide
    • Organic Vapors
  • Multi-Gas. Protects against organic, inorganic, chemical and ammonia based gases. All acid gases above, plus:
    • Ammonia
    • Formaldehyde
    • Hydrogen Sulfide
    • Methylamine
  • Multi-Gas / P100. Protects against organic, inorganic, chemical and ammonia based gases, and particulates.
  • Reuse your respirator over and over again with the standard-profile line of GVS replacement filters.
• NIOSH Approved TC-84A-8062.

NOTE – This is the standard profile series. Low-profile Elipse masks are also available.

As with all close-fitting respirators, these are designed to be used where fit-testing is conducted. The GVS Portacount Adapter is available to facilitate this testing.

The Bristle Blaster® is a portable surface preparation tool that combines wire wheels with an ingenious accelerator bar*, to speed production. Benefits include the following:

• Excellent for spot work.  Small projects such as rework, weld cleaning, etc., are faster due to no abrasive cleanup needed.
• Highly portable.  Light weight and compact makes usage and storage a breeze.
• Simple to use.  No need to suit up to use it.
• Quick setup.  Plug in and go!
• Safe for most surfaces.  Unlike a grinder, the Bristle Blaster® creates a surface profile without removing metal.

While the production speed isn’t as high as traditional abrasive blasting, the benefits of no mess and quick setup/teardown make this a very efficient tool for spot work and repairs.  It is up to 10x faster than using a hand wire brush. The Bristle Blaster® tools are available in 3 power configurations:

• Electric.  Requires 910 watts at 120v.
• Pneumatic.  Uses standard shop-air line.  Requires less than 20 CFM at 75 or 90PSI.
• Cordless.  Rechargeable battery power offers the ultimate in portability.

There are 3 orientation configurations for the wheels, as follows:

• Standard wheel (general purpose)
• Double wheel  (faster production for larger surfaces).  Note – available in electric only.
• Axial (right angle) wheel (great for reaching inside corners or other areas difficult to reach with the standard wheel).  Note – available in pneumatic only.

Additional notes:

• These units create a surface profile between 2.5 and 3.5 mils.
• Wire wheels are also known as belts.  BlastOne stocks all carbon steel and stainless Bristle Blaster® replacement belts.
• The standard pneumatic kit includes a dust shroud for attachment to a vacuum cleaner, for even faster clean up.
• Other belt types and machine models available – enquire.

*The Axial version does not come with an Accelerator Bar.

The GMA GX2 ToughBlast Garnet Abrasive (P-GX2) is a high-performance abrasive designed for challenging industrial maintenance tasks. Offering a high surface profile from 3.0 – 3.75 mil, this abrasive ensures an exceptionally clean surface, perfect for high build coatings. With blasting rates up to 370 ft²/hr and a low to medium dust factor, it’s ideal for rapidly removing heavy coatings and rust, especially in heavy-duty environments like offshore rigs and ship hulls.

• High surface profile from 3.0 – 3.75 mil for optimal coating preparation
• Blasting rates up to 370 ft²/hr for efficient operation
• Consumption rate of 1.5 – 3.0 lb/ft²
• Low to medium dust factor for cleaner work conditions
• Available in mesh sizes 16 and 36
• Packaged in 4400lb bulk bags, sold by the pallet
• MilSpec Approved for top-grade quality

GMA GX3 ExtremeBlast Garnet Abrasive is  ideal for surfaces requiring a high profile of 3.5 – 4.5 mil, ensures an exceptionally clean surface for superior bonding of specialist coatings. With blasting rates of up to 280 ft²/hr and a recyclability rating of 4/10, it’s perfect for removing resistant coatings, heavy liners, and marine foulings, especially on high build coatings of 30+ mils.

• High surface profile of 3.5 – 4.5 mil for exceptional coating bonding
• Impressive blasting rates up to 280 ft²/hr
• Consumption rate of 2.5 – 3.5 lb/ft²
• Low to medium dust factor for cleaner operations
• Available in mesh sizes 16 and 36
• Packaged in 4400lb bulk bags, sold by the pallet
• MilSpec Approved for top-grade quality

Crushed and Glass Bead Blasting Abrasive Media, SKU: P-CG. Perfect for steel profiling, available in various grades & sizes. Not for aluminum/stainless.

• General Purpose abrasive used for Sandblasting
• Angular shape creates a profile on steel
• Not Recommended for blasting on stainless or aluminum
• Comes in many different grades and packaging sizes
• Non-Recycling

• Copper Slag AKA Iron Silicate abrasive used for Sandblasting
• Angular shape creates a profile on steel
• Mohs Hardness of 7
• Bulk Density: 100-120 lbs/ft2
• Less then 0.1% free silica
• Not Recommended for blasting on stainless or aluminum
• Comes in many different grades and packaging sizes
• Non-Recycling
• Meets SSPC-AB 1 Standard
• Sold by the pallet (pallet minimum)
• Abrasive cannot be ordered online at this time

• Black Beauty Iron Copper Slag is a high-density slag abrasive for sand blasting
• Less then 0.1% free silica
• Mohs Hardness of 6-7
• Bulk Density: 100-120 lbs/ft2
• Not Recommended for blasting on stainless or aluminum
• Comes in many different grades and packaging sizes
• Non-Recycling
• Passes 40CFR 261.24a (TCLP)
• Passes SSPC AB-1
• Sold by the pallet (pallet minimum)
• Abrasive cannot be ordered online at this time

From the makers of the Nova Respirators!

• GVS Masks are made from TPE and are hypoallergenic and non-irritating.
• Extremely lightweight and comfortable.
• Each mask includes the initial set of filters installed and is ready-to-use.
• Price shown per-each.  Packed 5 per case, with case discount.
• Multiple filter versions available as follows:
  • Standard P100
  • Enhanced P100 w/Nuisance Odor control
  • OV / P100 – P100 Organic Vapor protection.  Painters favorite!
  •  Reuse your respirator by using the low-profile line of GVS replacement filters, which include a pre-filter option which extends the life of the OV / P100 filter.
• NIOSH Approved goggles provide ANSI Z87+ eye protection.
• Goggles are scratch and fog resistant.  Tear-off lenses available separately to keep them clean while spraying

NOTE – This is the low-profile series with enhanced field of vision. Standard-profile Integra Masks (which offer Acid Gas & Multi-Gas filter options) are also available.

Your regular eyeglasses will not fit under these goggles. However, GVS makes an Integra Prescription Lens insert to fit inside, which you can give to your optician to have fitted with your prescription.

As with all close-fitting respirators, these are designed to be used where fit testing is conducted.  The GVS Portacount Adaptor is available to facilitate this testing.

THe GMA SoftBlast Garnet Abrasive (SKU: P-GAFINE), is the softest abrasive in the GMA range, perfect for cleaning and polishing delicate surfaces. Achieving a surface profile of 0.5 – 1.0 mil (12 – 25µm) or less, it offers blasting rates up to 300 ft²/hr. With a low consumption rate of 0.75 – 2.0 lb/ft² and a recyclability rating of 1/10, this super fine garnet abrasive is ideal for tasks like historic monument cleaning, graffiti removal, and mold and mildew removal from log cabins.

• Super fine garnet abrasive for delicate surface work
• Surface profile of 0.5 – 1.0 mil for gentle cleaning and polishing
• Blasting rates up to 300 ft²/hr
• Low consumption rate for economical use
• Low dust factor for cleaner operations
• Mesh sizes of 200 and 350 for ultra-fine applications
• MilSpec approved, ensuring top quality
• Sold by the pallet (pallet minimum)
• Abrasive cannot be ordered online at this time

The PosiTest OTL – DeFelsko’s solution to monitor and record temperature profiles in Powder Coating and other industrial ovens. Configurable in various ways, some of it’s features include:

• Simple Design.  With an easy-to-use interface and bright LED’s to indicate logger status, operating the Oven Temperature Logger is simple and intuitive.
• Capable.  The DeFelsko OTL can:
  • Measure & record up to 40,000 datasets in up to 6 batches. Records temperatures every 2 seconds for up to 22 hours.
  • 6 ‘Channels’ (K-type thermocouple ports) for adding temperature probes.
• Configurable.  Depending on the specific application, the OTL offers various configurations, such as:
  • PosiTest OTLKIT, including logger with barrier box and standard Holder (65 minute endurance at 200° C)
  • PosiTest OTLKITXT, same as above, except with heat-sink Holder (200 minute endurance at 200° C)
  • (See sliding scale endurance chart on the brochure under the Documents tab)
  • OTL logger only without barrier box, for use with temperature probes and when the logger does not need to be in the oven.

Note:  See the selection of temperature probes on the You May Also Like below.

• Ideal for Blasting: Milscale – 5 ml coating removal
• Unique formulation, ideal for blasting structural steel, bridges, general purpose blasting
• Blend has large particles designed to effectively remove existing coatings and finer particles to thoroughly clean the rusted pits and surface.
• Expected Profile 2.5 – 4.0 ml
• Abrasive Consumption 2.5 – 5.0 lb/ft²
• Blasting Rates up to 370ft² /hr
• Sold by the pallet (pallet minimum)
• Abrasive cannot be ordered online at this time

• Ideal for removing coating thickness: 5-15 ml
• Unique formulation, engineered to prepare pipework surfaces for coating
• Typically used in the petroleum and water utility industries
• Blend has large particles designed to effectively remove heavy coatings and finer particles to thoroughly clean the pits and surface.
• Expected Profile 2.5 – 4.0 ml
• Abrasive Consumption 2.5 – 5.0 lb/ft²
• Blasting Rates up to 370ft² /hr
• Sold by the pallet (pallet minimum)
• Abrasive cannot be ordered online at this time

• Designed to remove Coating Thickness: 20-50 ml
• Unique formulation, ideal for blasting marine offshore, oil and gas, shipyards
• Typically used where heavy coatings and rust are existing
• Blend has large particles designed to effectively remove heavy coatings and finer particles to thoroughly clean the pits and surface.
• Expected Profile 2.5 – 4.0 ml
• Abrasive Consumption 2.5 – 5.0 lb/ft²
• Blasting Rates up to 370ft² /hr
• Sold by the pallet (pallet minimum)
• Abrasive cannot be ordered online at this time

• Coating Thickness Range:  10-50 mil
• Unique formulation, ideal for blasting storage tanks
• Blend has large particles designed to effectively remove heavy coatings and finer particles to thoroughly clean the pits and surface.
• Expected Profile 2.5 – 4.0 mil
• Abrasive Consumption 2.5 – 5.0 lb/ft²
• Blasting Rates up to 370ft² /hr
• Sold by the pallet (pallet minimum)
• Abrasive cannot be ordered online at this time

• Turns your cell phone or tablet into a virtual PosiTector gauge
• Accepts coating thickness, environmental and surface profile probes
• Mobile integration operates via bluetooth – no internet connection required
• Kit includes holster with belt clip, wrist strap, PosiTector app, batteries
• Probes purchased separately

Recommended best practice when using the PosiTector RTR 3D is to use these specialized Replica Tape Holders.

Very easy to use – just affix the replica tape to the holder, and ensure that the compressible foam is located over the hole in the holder. Once adhered, the replica tape can be simply placed into the probe with no concern about migration of the adhesive onto the probe sensors.

Recommended best practice when performing replica tape tests is to thoroughly clean the surface before attaching the film to the substrate.

This Surface Cleaning Putty is excellent for cleaning steel surfaces of dust and abrasive.  One package comes standard with each new PosiTector RTR and additional quantities are available here as needed, in packs of 5.

Recommended best practice when performing replica tape tests with PosiTector RTR instruments is to thoroughly clean the anvils (test surfaces) before performing the test.

These Cleaning Cards are premoistened with alcohol and are excellent for removing bits of adhesive and debris from the anvils. Each new RTR comes complete with 5 cleaning cards and additional quantities are available here as needed, in packs of 20.

Burnishing tools facilitate accurate and easy use of Testex Press-O-Film replica tape.  Multiple types available, as follows:

• Stick-type.  Economical plastic, sold in packs of 10, these have 8mm round ends.  Use with all types of Testex tape.
• Burnishing ball.  Designed to use with optical grade tape, for use with the RTR 3D probe.
• High Accuracy tool.  Updated with a spring-loaded ball for the most consistent results.  Use with standard Testex tape.

DeFelsko oven temperature probes for use with their OTL system: Extend the reach of the logger with the wide selection of probes as follows:

• Applications.  Available in both Surface and Air types.
• Mountings.  Available in Magnetic, Clamp, and Washer mounts.
• Lengths.  Stainless braided cables commonly stocked in 3 lengths, and custom lengths available by special order.

Replacement filter cartridges to suit GVS Elipse and Integra Low-Profile half masks.

• Standard P100. These filters will remove up to 99.97% of particles and contaminants down to 0.3 microns.
• Enhanced P100 w/ activated charcoal. Designed to remove nuisance odors along with P100 filtration.
• OV / P100. Protects against organic vapors and particulates.
• Prefilters.  Optional filters designed to extend the life of the OV filter.  Requires filter holder kit as shown.

NOTE – This is the low-profile series. The standard-profile series is available here.

Genuine GVS product.

• Items in this kit include:
  • Standard Coating Thickness Gauge
  • Wet Film Thickness Combs
  • Whirling Hygrometer
  • Magnetic Surface Thermometer
  • Testex Surface Profile Test Kit
• The BlastOne range of coating inspection kits facilitate for every type of coating inspector – protective coating, industrial, marine, etc.
• Three ‘off the shelf’ kits are available – will suit a diverse range of inspection applications
• Custom designed kits are also available – please discuss your requirements and application with BlastOne

The Steel Shot Blasting Abrasive is a highly durable and long-lasting peening media, ideally suited for use in airless wheel blast machines for applications like cleaning foundry castings, surface polishing, shot peening, and concrete floor preparation. Available in a variety of grades and sizes, this steel shot is designed for a high-quality performance, conforming to SAE J444, SAE J827, SFSA 20-66 standards, and can be recycled multiple times, offering an economical and effective solution for shot blasting needs.

• Steel shot – manufactured hypereutectoid, metal spheres used in airless centrifugal wheel blast machines to clean foundry castings, surface polishing and shot peening
• Also used in portable trackblast airless wheel blast machines for concrete floor preparation, blasting ship decks and profiling
• Quality Steel Shot is very long lasting
• Steel Shot can be recycled many times
• Hardness: 40-50 HRc. Other hardness’s of steel shot are available on request
• Special, Stainless Steel Shot and High Hardness, Milspec (Military Specification Peening Steel Shot) specification shots available
• Manufactured to conform to: SAE J444, SAE J827, SFSA 20-66
• Steel Shot is packed in 25kg bags, drums or bulk bags

• Pinovo Pico is one of the most ingenious vacuum blasting discoveries in 10 years
• Hand-held dustless external pipe blasting system.
• Multiple different sized work-heads adapt to different sized pipe.
• Works for 2″ – 8″ pipes
• Genuine Parts – Manufactured by Pinovo in Norway
• Minimal Availability in USA – Request a quote/express interest

• For enhanced stability on 30-45cm (12-18″) OD pipes
• For PosiTector SPG OS only

• The PiBlast is designed for automatic blast cleaning of metal pipes.
• This system allows for efficient pipe blasting without the investment of a permanent installation.
• Has 4 blast nozzles which each blast 1/4 of the pipe
• Only available to blast 8″
• Genuine Parts – Manufactured by Pinovo in Norway
• Not Available in USA – Request a quote/express interest

Coating Inspectors – save time and cost by choosing a deluxe PosiTector® coating inspection kit.  Details on the most popular configurations are as follows:

• Standard Instrument Package:
  • Includes PosiTector 6000 Standard body, DPM and SPG probes and choice of coating thickness probe.
• Advanced Instrument Package:
  • Same as Standard Package but with Advanced body.
• Extreme Package:
  • Same as Advanced Inspection Package with added DPM-L data-logging climatic condition probe, RTR-H replica tape reader and Testex X-tra coarse tape.  The FS (standard-range, cabled, ferrous) is the coating thickness probe included in this package.
• Each Package also includes:  a carry case, calibration certificate, plastic shims, and more!

For custom configurations, contact us by chat, phone, or email for prompt response.

GMA ExtremeBlast 36 Mesh Garnet Abrasive (SKU: P-GM36) is the ultimate solution for removing tough specialist coatings, heavy liners, and marine foulings. This coarse-grade abrasive is perfect for tackling high build coatings of 30+ mils, offering blasting rates of up to 260 ft²/hr. With its uniform surface profile of 3.5 – 4.5 mil and a low to medium dust factor, it achieves an exceptionally clean surface, ensuring strong bonding of specialist coatings. Ideal for critical applications like TSA preparation and extreme condition coatings, this abrasive is a top choice for the removal of high build, pliable, and flexible coatings, including coal tar and marine coatings.

• Coarsest grade garnet for resistant coating removal
• Effective on high build coatings over 30 mils
• Blasting rates up to 260 ft²/hr, creating a 3.5 – 4.5 mil surface profile
• Low to medium dust factor and excellent surface cleanliness for optimal coating adherence
• Efficient consumption rate as low as 2 lb/ft²
• Recyclability rating of 4/10
• Perfect for TSA preparation, extreme condition coatings, and critical component preparation
• Ideal for offshore platform decking, tanks, piping, pressure vessels, ship hulls, and ballast tanks
• Available in 16 and 36 mesh sizes
• Packaged in 55lb bags, and 2200lb & 4400lb bulk bags
• Sold by the pallet for bulk needs

The GMA GX1 SpeedBlast 30/60 Garnet Abrasive (SKU: P-GX1) is a MilSpec Approved, versatile maintenance grade abrasive. Perfect for removing light to medium coatings and rust, it efficiently produces a surface profile from 2.5 – 3.25 mil (65 – 85 µm). With blasting rates up to 350 ft²/hr and a low dust factor, it’s ideal for general industrial maintenance, including construction, chemical plants, and more. Packaged in 4400lb bulk bags and available in mesh sizes 30/60 and 80, this garnet abrasive is sold by the pallet.

• MilSpec Approved, high-quality garnet abrasive
• Efficient surface profile creation from 2.5 – 3.25 mil
• Blasting rates up to 350 ft²/hr for rapid surface preparation
• Low consumption rate of 1.5 – 3.0 lb/ft²
• Low dust factor for cleaner operation
• Recyclability rating of 5/10
• Available in mesh sizes 30/60 and 80
• Packaged in 4400lb bulk bags, sold by the pallet

The GMA PrecisionBlast 120 Mesh Garnet Abrasive (SKU: P-GA120), is a MilSpec Approved abrasive ideal for delicate surface preparation. Offering a fine surface profile of 1.0 – 2.0 mil (25 -50µm) or less, this abrasive boosts blasting rates up to 330 ft²/hr and a low consumption rate of 1.25 – 2.0 lb/ft². Its low dust factor and recyclability of 2/10 make it perfect for precision tasks on sensitive substrates like stainless steel, aluminum, titanium, and glass.

• Creates a fine surface profile of 1.0 – 2.0 mil
• High blasting rates up to 330 ft²/hr
• Low consumption rate of 1.25 – 2.0 lb/ft²
• Low dust factor for cleaner operations
• 120 mesh size for delicate cleaning tasks
• Ideal for etching glass and preparing sensitive metals
• Sold by the pallet (pallet minimum)
• Abrasive cannot be ordered online at this time

The GMA CLASSIC CUT 80 MESH Garnet Abrasive Media (SKU: P-GANS) is an all-around abrasive ideal for sandblasting new steel and preparing surfaces for coating. This #80 grain size garnet is perfect for achieving a 40-60 micron profile, offering a typical consumption rate of 250 kg/hr and blasting rate of 20 m²/hr. Its pinkish to reddish-brown, sub-rounded grains deliver high performance with low dust, making it an economical choice for both single-use and recycling.

• #80 grain size for efficient sandblasting
• 25-50 micron surface profile ideal for new steel and mill scale removal
• Low dust, high performance garnet abrasive
• Economical with a typical consumption rate of 250 kg/hr
• Blowing rate of up to 20 m²/hr for millscale removal
• Suitable for a variety of industrial applications
• Packaged in convenient bulk sizes

• Walk-behind vacuum blasting head
• Will Blast a 4″ wide blast strip – widest of any blast and vac workhead
• Nozzle size: No.6 (⅜”)
• Blasting rate: up to 64 ft²/6 m² per hour.
• Compressed air requirement: 500 cfm.
• Surface preparation standards compliance capability: up to SA 3 / SSPC-SP-5 / NACE No. 1.
• Achievable surface profile: 110 µm, depending on blast pressure, grit size, and surface.
• Noise level: 89 dB at 1m distance.
• Mounted with Wheels, making it easy to maneuver
• Has replaceable rubber lining and brushes.
• Genuine Parts – Manufactured by Pinovo in Norway

Limited availability in the USA – Request a quote/express interest.

• 4″ (100 mm) wide roller
• 12″ Long Frame
• Thin profile for tight access
• threaded handle for pole adapter

• The PiPoint is the smallest hand-held vacuum blasting tool.
• Has 8 interchangeable heads providing flexibility for different job requirements.
• Allows you to blast inside a small box web beam, etc.
• Nozzle size: No.6 (⅜”)
• Blasting rate: up to 6 ft²/0.6 m² per hour.
• Compressed air requirement: 250 cfm.
• Surface preparation standards compliance capability: up to SA 3 / SSPC-SP-5 / NACE No. 1.
• Achievable surface profile: 110 µm, depending on blast pressure, grit size, and surface.
• Noise level: 89 dB at 1m distance.
• Genuine Parts – Manufactured by Pinovo in Norway

Limited availability in the USA – Request a quote/express interest.

The PosiTector®SHD – DeFelsko’s solution for measuring shore hardness on non-metallic surfaces.  Capable and configurable, it offers the following:

• Familiar.  Built on the tried-and-true PosiTector gauge / body platform, with interchangeable measurement probe options.
• Capable.  The SHD comes in two probe models for different hardness ranges.
  • Shore A (soft to hard materials such as soft rubber, elastomers, neoprene, silicone, etc.
  • Shore D (medium to extra hard materials such as hard rubber, hard plastics, epoxies, PVC, acrylic, etc.
• Configurable.  Available as follows:
  • Probe only.  Use with your existing PosiTector gage.
  • Standard PosiTector package with choice of probe.
  • Advanced PosiTector package with choice of probe.
  • Note:  All PosiTector SHD packages come with case, test block, calibration certificate, holster, and more.

Note:  Compare specs and features of the DeFelsko Standard and Advanced Gage / Bodies on their separate web page.

• Nook ‘n’ Cranny Roller Frame suits a 4″ roller
• 24″ Long Handle to give you more reach
• End of handle has threads for attaching to standard extension poles
• Used to get the hard bits to reach or roll with a larger roller.
• Sold Individually without the roller covers

The deflection tip in the ConeBlast Jr. internal pipe blaster is responsible for ensuring an even blast pattern.  The abrasive stream hits the tip and fans out in a 360° pattern.  It is subject to high wear and is a common replacement part.  Additional details:

• Application:  This tip works only in the ConeBlast Jr., not the larger ConeBlast version.
• Construction:  This tip is made from tungsten carbide.  For large pipe-cleaning projects, contact us for options on longer-life versions.

The innovative and capable PosiTector Gage / Body is the backbone of a large and growing family of DeFelsko inspection equipment. When paired with 1 of the over 10 interchangeable probes, it can measure and store data for common environmental, surface, coating and more conditions.  

DeFelsko offers two versions of gauges (Standard and Advanced) which can be purchased individually, or in a variety of DeFelsko Body / Probe packages including 1 or more probes, depending on the application.  To compare features on the two gage versions, see our PosiTector 6000 Standard and Advanced Body comparison chart.

This page shows the Gage Body options only.  BlastOne carries all other DeFelsko items including individual PosiTector 6000 probes, PosiTector Standard Body/Probe Kits, PosiTector Advanced Body/Probe Kits, and DeFelsko Coating Inspector Packages.  

NOTE:  This new Gen 5 PosiTector body platform is backwards-compatible with all Positector probes manufactured since 2012.

FAN BLAST™ Fan Pattern SiALON Blast Nozzles give wide, even blast patterns, ideal for sweep blasting. Different variations include:

• 2″ UNC (50mm) coarse contractor thread
• 1-1/4″ ( N.P.S.M.) fine industrial thread

Also available with tungsten carbide liner – enquire for price and lead time.

At present, this nozzle is available only with a #6 orifice.  An alternative nozzle type for this application, which is available in multiple orifice options, is the Raptor / Bazooka nozzle.

• • • FREE Shipping
    • 30 Day Money-Back Guarantee | Free Returns
    • 8″ cutting width
    • Easy to use, maintain and maneuver
    • Precise screw type scaling head adjustment
    • Angled dust port allows connection of industrial dust collector giving virtually dust free performance
    • Supplied complete & ready to work with cutter head
    • Updated version with improved electrics and start switch

Also available in 120v electric, as well as pneumatic and gas power.

The BlastOne Abrasive Testing Kit comes with six (6) officially standard (ASTM E11 Specification) stacking sieves as well as a graduated cylinder, funnel, and carrying case.  The sieve trays are rated for the following particle sizes:  40 mesh  (425 microns) |  50 mesh  (300 microns) |  80 mesh (180 microns) |  100 mesh (149 microns) | 140 mesh  (106 microns) | 170 mesh (88 microns)

The BlastOne Abrasive Testing Kit comes with six (6) officially standard (ASTM E11 Specification) stacking sieves as well as a graduated cylinder, funnel, and carrying case.  The sieve trays are rated for the following particle sizes: 30 mesh  (600 microns) |  40 mesh  (425 microns) |  50 mesh  (300 microns) | 60 mesh (250 microns) |  80 mesh (180 microns) |  100 mesh  (149 microns)

FREE Shipping

30 Day Money-Back Guarantee | Free Returns

90 Day Manufacturer Warranty

• The most versatile, easy-to-regulate dry blast machine on the market
• 10-150psi blasting pressure range
• With a load skid combined with an inlet filter, this product uses a differential pressure gauge to allow accurate “metering” of hard-to-flow abrasives like Soda and fine Garnets
• With regulators for the blast and tank pressure for accurate control, this product can be used with most abrasive types – fine to coarse
• With the addition of a media vibrator to improve light media flow and an easy-to-use media shut-off valve this unit is perfect for graffiti removal and all other types of soda blasting
• G2 pneumatic deadman control, 55′ twinline control hose, 55′ water line with wet blast attachment for dust suppression included with purchase

Genuine Products – Manufactured by Schmidt® / Axxiom Manufacturing

• 2-pin Twistlok plug
• For use with Clemco remote control systems only

When your scaling hammer needs refreshed, we have the replacement parts you need. This is the Trelawny O-Ring Square Section (809.0089).

Stainless Steel Shot

• Manufactured chronital stainless steel shot abrasive
• Can be recycled many times
• Stainless Steel Abrasives are also used in applications where there can be no ferrous contamination
• Used mainly in an air-blast application to create a specific desired finish or where a non-ferrous abrasive is required
• Sharp edges gradually round over as it wears
• Packed in 25kg bags
• Made by Vulkan Shot
• Grittal Stainless Steel Grit also available

• A lightweight closed-circuit vacuum blaster with interchangeable heads.
• Edge blasting tools.
• Nozzle size: No.6 (⅜”)
• Blasting rate: up to 27 ft²/2.5 m² per hour.
• Compressed air requirement: 320 cfm.
• Surface preparation standards compliance capability: up to SA 3 / SSPC-SP-5 / NACE No. 1.
• Genuine Parts – Manufactured by Pinovo in Norway.
• Limited availability in the USA – Request a quote/express interest.

Sponge-Jet blast media is unique in the field of abrasive blasting. (See How it Works under the Description tab.)

Depending on project requirements, many versions are available as follows (all versions use original sponge carrier unless noted):

• Silver Sponge series.  Incorporates aluminum oxide abrasive.
  • 16 to 320 mesh available, with the most common coating removal versions being Silver 30 or Silver 60.
  • A DG (Double Grind) version is offered in the 30 and 60 mesh.  This version is pre-processed to function like a working blend immediately, with up to 75% faster blast speed initially compared to original sponge abrasive.
• Red Sponge Media.  Incorporates steel grit abrasive.
  • Highly aggressive and typically used to remove pack rust and/or pitting.
• White Plastic Sponge Media.  Incorporates Type II 30/40 mesh plastic urea.
  • Lightly aggressive and used for coating removal without etching / profiling on steel or aluminum.
• White SPOCC Sponge Media.  Incorporates Spherical Precipitate of Calcium Carbonate.
  • Lightly aggressive and used for contaminant removal.
• White Glass Bead Sponge Media.  Incorporates 60/80 mesh glass bead.
  • Lightly aggressive, used for soft alloy substrates where a low-build coating system will be used.
• Green Sponge Media.  Incorporates Wollastinite cleaning agent.
  • Lightly aggressive, used for contaminant removal where moisture is not present.
• HyperX Media.  Proprietary blend of aluminum oxide and other medias.
  • Available in Medium or Coarse for 2 or 3 mil profile.
  • Uses a higher ratio of abrasive-to-sponge, for faster production than even the Double Grind.
  • Lower in cost, but not as effective in dust capture and with some ricochet, this media is best suited inside tanks or pipelines where 100% containment is assured.
  • Hyper X media requires a specific 3-screen setup using the 70 series recycler (#3, #16, and #50)
• Super Media-1. Incorporates a blend of steel & ceramic abrasives.
  • Highly aggressive, used for concrete blasting to expose aggregate, rubber lining removal on steel, lead paint removal in a demolition project, etc.
  • When blasting on steel, this product creates such a high profile (8 mil plus) that some of the sponge will embed.  If recoating, an additional cleaning process will be required using a steel brush, Bristle Blaster, etc.

All sponge media is packed 55 bags per pallet, with price breaks available at 1 pallet and at 6 pallets+.

Note:  Due to our distribution agreement with Sponge-Jet, pricing is not shown on our website.  Contact us for fast, competitive pricing or send in the web-form quote request.

BlastOne offers all accessories and replacement parts for DeFelsko testing instruments.

The PosiTector Surface Profile Gauges have replaceable tungsten carbide tips and are available as follows:

• 60° Angle for ASTM (USA) applications, used in the Integral, Standard Cabled, and Convex Cabled probes.
• 30° Angle for AS 3894.5-C (Australia) applications, also used in the Integral, Standard Cabled, and Convex Cabled probes.
• CS Tip for Textured Coatings probes.
• TS Tip for Concrete Surface probes.

These tips ensure accurate measurement of surface profile and should be replaced when worn.

Each tip includes a tool to facilitate replacement.

RENT or PURCHASE this surface preparation work-horse!

The next-generation V400 Ultra High Pressure VertiDrive. Bringing enhanced technology to closed-loop UHP projects.

• Faster.  V400 robotic technology is up to 5X faster than manual work.
• Cleaner.  The rust, coatings, and contaminants are removed and returned to the vacuum via the closed-circuit system.
• Safer.  Remote control operation removes the operator from harms way.
• Capable.  Boosted magnetic performance allows standard operation on carbon steel surfaces that are horizontal, vertical, and even upside-down!
• Environmentally friendly.  Contaminants don’t just fall to the surface or blow away in the wind.  The V400 brings them back to the vacuum source for responsible disposal.
• Productive.  Has an extra-wide 15.5″ (400 mm) cleaning width

Note:  UHP does not create surface profile , but exposes the existing profile.

We recommend that this equipment be used on large, flat surfaces (like tanks or ship hulls) with at least 10,000 square feet to realize cost savings.  Can be used with existing UHP pumps or BlastOne can arrange.  Purchase pricing is typically between $165,000 and $204,000 depending on configuration.

BlastOne can provide on-site training and ongoing support to ensure maximum productivity from Day 1.  Schedule a call with our SMEs to calculate an expected ROI for your next project.

• Recommended for large inspection projects, complex specifications and regular use
• Covers coating thickness, surface profile, climatic conditions and adhesion testing and surface chloride testing
• Items in this kit include:
  • PaintGage coating thickness gage – memory model, separate or integral probe with software
  • Certified coated thickness standard
  • DewCheck electronic climatic gage
  • 10 x aluminum wet film combs to 1 to 80 mil (25 to 2032 micron) range
  • Magnetic surface thermometer -22°F to +122°F (-30°C to +50°C) range
  • Testex surface profile test kit – includes dial thickness gage, 100 Testex tape tests and burnishing tools
  • Surface comparators with illuminated magnifier
  • Cross hatch adhesion test kit – includes cross hatch cutter and ISO roll of tape
  • S20 hazardous area inspection light
  • Five x Chlor*Test surface chloride tests
  • Retractable inspection mirror

• Close fitting medium impact eye protection
• Most styles available with clear or tinted lenses – styles can vary
• A range of chemical safety goggles are also available:
  • Low profile, extremely lightweight, comfortable with unique ventilation system
  • Anti fog/anti scratch
• Sold as a box of 12
• Genuine Parts – Manufactured by Pyramex

• Suits BABL2106 Brickette Blast Area Light
• The Long Handled, High profile Magnetic Handle can be used a multitude of ways including:
  • Magnetically attach to steel pipes, beams or walls
  • Use the handle to hang over ropes, scaffold tubes or pipework
  • The handle is large enough to act as a sturdy base for floor mounting as well
• Sold Individually
• Genuine Part – Manufactured by Western Technology

• Effective Replacement for Dupont StarBlast
• Single use mineral sand abrasive blast media.
• Typical applications include: Mill scale, light rust and new steel
• Mohs hardness of around 7
• Expected profile range of 1-2mils
• Blasting Speeds between 75 – 150ft²/hr
• Typically has a high dust burden
• Sold by the pallet (pallet minimum)
• Abrasive cannot be ordered online at this time

• Chlor*Rid is a liquid soluble salt remover, which includes chlorides, nitrates, and sulfates
• Typically used as part of the surface preparation process prior to application of coatings.
• Apply using a pressure washer before you blast.
• Removing them prior to blasting means they will not be blasted into your profile and decrease the risk of coating failures
• Sold in 5-gallon drums
• Genuine products – manufactured by Chlor-Rid

• Highest level of durability and low vibration with steel cut spiral bevel gears
• Increases user productivity
• Offers greater comfort and control with two position side handle
• Enhanced application versatility with keyless guard
• Improved gear durability with low profile jam pot
• Quick and easy wheel removal with quick change wheel release

AVAILABLE FOR RENT OR PURCHASE

• Newest member of the Graco King family, designed for increased portability and affordability.
• Unparalleled finish quality with cutting-edge anti-icing technology
• Robust, low-profile design offers extreme mobility
• XL6500 Air Motor
• Purchase package includes Silver Plus™ Gun, 3/8″ x 50ft hose, 1/4″ x 6′ whip hose, XHD 417, 519 SwitchTip™ & Guard