Search: blast pots

FREE Shipping

30 Day Money-Back Guarantee | Free Returns

90 Day Manufacturer Warranty

• Abrasive holding capacity of 3.5 cu ft
• Blasting rate up to 40 ft² per hour
• Compressed Air Requirement 750 cfm
• Includes fork pockets
• Can be wheel mounted for increased jobsite maneuverability
• Recirculating full size blast & recovery unit
• 100% compressed air driven – no electricity required

Genuine Products – Manufactured by Schmidt / Axxiom Manufacturing

For rental or purchase

• The Nova 3 Blast Helmet is the industry #1 for operator comfort
• Has comfort padding inside like a motorcycle helmet, which means it distributes the weight evenly, and also turns with your head
• Gives up to 20dB noise attenuation
• NIOSH Safety Approval with a 1000 APF (assigned protection factor)
• Sold as a complete kit with the following variations: 
  • Cape Options: 
    • Standard Length Nylon Cape
    • Extended Nylon Cape
    • Standard Leather Cape
    • Extended Leather Cape
    • XL Blast Jacket
    • XXL Blast Jacket 
  • Climate Options: 
    • Supplied air offers: 
      • C40 Heating and Cooling
      • Cool Air Tube
      • Hot Air Tube
      • Air Control Valve
    • PAPR offers: 
      • Air Control Valve only
      • (PAPR version is intended for low dust applications such as pot tending, inspection, etc.)
• Genuine Products – Manufactured by RPB Safety

Portable Sponge-Jet® feed units (aka Sponge Pots) come in a variety of configurations to suit almost every application.  From small, value-based units to fully featured machines, sponge feed units are designed for the ultimate in low-dust abrasive blasting. Seven configurations are available, as follows:

• RASP Xtreme™ 3:
  • Highly portable & fits thru a 24 inch manway
  • Holds 1 bag of new sponge media (5-7 minutes)
  • Includes pressure relief valve (PRV) & integrated wheels
  • Great for spot work
  • 127 lb. empty weight
• 100-HP Feed Unit™:
  • Great balance between size, cost & blast time
  • Fits through a 30″ doorway
  • Holds 3 bags of new sponge media
  • Includes PRV, secondary moisture separator & wheels
  • Great for preservation work
  • 480 lb. empty weight
• CG Series (Contractor Grade Series):
  • 2 sizes available:
    • 170-CG – holds 5 bags of new sponge media
    • 470-CG – holds 13 bags of new sponge media
  • Value series – ideal where few features are required
  • Includes fork pockets
  • Great for yard work
  • 600 lb. / 1142 lb. empty weights for 170-CG / 470-CG
• SJ Series (Feed Unit Series):
  • 2 sizes available:
    • 170-SJ – holds 5 bags of new sponge media
    • 170-EX – similar to 170-SJ, but ATEX 2 rated for potentially flammable environments
    • 470-SJ – holds 13 bags of new sponge media
  • Fully featured, includes:
    • Pressure relief valve
    • Secondary moisture separator
    • Muffler
    • Frame w/casters and lifting lugs
    • Centralized controls
  • Great for field work
  • 900 lb / 1000 lb / 1515 lb empty weights respectively

All new feed units come with choice of WEV or Saber nozzle.  We recommend the Saber nozzle due to it’s much higher value.  In addition, optional equipment such as the manifold/moisture separator, the vacuum drums, etc. are less costly if purchased when a feed unit is purchased.

Note:  Due to our distribution agreement with Sponge-Jet, pricing is not shown on our website.  Contact us for fast, competitive pricing or send in the web-form quote request.

• Compatible with a wide range of blast pots
• Digital display of actual blasting time for individual blast outlets
• Allows you to determine productivity, production rates, assisting project costings, job estimates and scheduling maintenance for common wear items
• System available to run off pneumatic and electric deadman controls
• Triggered instantly by the deadman signal, so you get actual blasting hours
• Options available for single and multiple outlets.

FREE Shipping

30 Day Money-Back Guarantee|Free Returns

90 Day Manufacturer Warranty

• Most common contractor size, combining portability with productivity
• When using premium garnet media, this pot will blast for around 1.5 hours before you need to refill
• Capacity of 6.5 cu ft, which equates to 950lbs of a dense media like premium GMA Garnet
• Pressure Rating: 150psi

Sold as a Kit which Includes:

• Blast Pot Deadman Control System with 50 feet of control line and handle
• Choice of inlet fitting in either 4-claw or Spud type. Spud will be supplied unless otherwise noted in Order Comments field

BLAST HOSE SOLD SEPARATELY

Genuine Products – Manufactured by Schmidt® /Axxiom Manufacturing

For rental or purchase

FOR RENTAL OR PURCHASE

• Ideal for blasting penstocks, tunnels, pipelines, wind towers, etc.
• Offers full 360 degree coverage of pipe internals
• Self-propelled forward or reverse motion
• Can blast pipelines 3′ – 32′ in diameter
• Lowers labor costs as much as 75% compared with manual blast-pot operations
• Eliminates inconsistencies commonly found with manual blasting

This kit includes all parts needed to change from blasting to blow-off at the flip of a switch at the deadman. Eliminates need for a separate air-hose or trekking back to the pot to shut off the abrasive.

This version is for pots with an existing Thompson 2 valve and pneumatic controls.

Convert your Pneumatic Blast Pots to Electric Deadman Systems seamlessly with the Pneumatic to Electric Deadman Blast Pot Conversion Kit (SKU: P-DMECK). Ideal for setups with over 100ft of blast hose. Kit includes connector box, battery cable, and more.

• Pneumatic to Electric Deadman Blast Pot Conversion Kit
• Used to convert Pneumatic Blast Pots over to Electric Deadman Systems
• Electric Deadman should be used on any set ups running over 100ft of blast hose
• Sold as a Conversion Kits including;
  • Connector Box
  • 16 feet battery cable with alligator clips
  • Response electric remote control handle
  • 55 feet  deadman cable
  • TwistLok plug connector
• Energy consumption rate of 8 watts per control valve
• Assembled by Qualified BlastOne Technicians

• 20 cu ft Blast pot
• Excellent for a blastroom application with 2 blasters
• Dual outlet Thompson Valve II abrasive metering valves
• Abrasive capacity
  • Garnet 2950 lbs
  • Steel Grit 4900 lbs
• Comes with two pneumatic deadman handles and two lengths of control hose (Electric Available)
• Genuine Products – Manufactured by Schmidt to BlastOne specifications

FREE Shipping

30 Day Money-Back Guarantee | Free Returns

90 Day Manufacturer Warranty

• Blasting rate up to 20 ft² per hour.  Due to this low production rate, this unit is intended for specialty applications, such as spot-work in dust-sensitive areas.
• Utilizes the TeraValve XL abrasive metering valve
• Compressed Air Requirement is only 185 cfm
• Has wheels and fork pockets for easy portability by hand, or by forklift.
• 100% compressed air powered – no electricity required
• Various workheads are available for flat surfaces, inside corners, outside corners, etc. – enquire for details.
• Genuine Products – Manufactured by Schmidt / Axxiom Manufacturing

Abrasive blasting hopper lid and mesh screen

• • Lid and Screen Set designed to suit blast pots
  • Hole size 1/8 (3 mm)
  • Screen sieves foreign matter out of the abrasive
  • Lid keeps moisture, rain, dew, etc out of the blast machine
  • Select the size to suit diameter of your blast pot 12″ 18″ 24″
  • Fit most portable blast machines, made by Schmidt abrasive blasting, Axxiom Manufacturing, Clemco

• Suits Pneumatic Blast Pot Control Valve DM2229000
• Service Kit is used to keep your blast pot operational
• Sold as a Kit containing;
  • Piston
  • Spring
  • Replacement O-rings

BULKBLASTER / MEGABLASTER

• Specified capacity 160 cu ft / 4500 liters
• Manufactured by Schmidt to BlastOne unique specifications
• Garnet abrasive capacity – 23800 lbs / 10.8 tonne
• 1600 cfm Airprep™ mounted directly on the front of the MegaBlaster
• Comes with 2 Thompson® Valve metering valves, up to 4 outlets possible
• Skid or Trailer Mounted
• Hybrid Bulk Blaster with built-in Air Dryer

FREE Shipping

30 Day Money-Back Guarantee | Free Returns

90 Day Manufacturer Warranty

• Versatile!  No need to have separate wet and dry blast equipment.  Wet blast or dry blast with a single unit
• Minimal water usage (less than 1 pint / ½ litre per minute) with proprietary Schmidt  technology that allows precise control of the amount of water injected into the air stream while blasting
• Abrasive tank is “dry” so there is no need to drain water to refill with abrasive. This creates a significantly cleaner job site and is more efficient
• Schmidt TeraValve™ XL abrasive metering valve offers precise and repeatable control of a wide range of coarse or fine abrasives
• Wide range of blasting pressure capabilities from 10 to 150 psi
• Toggle between wet blast, dry blast, wash-down and blow-off using a single control panel
• This version has a 3.5 C.F. capacity.  Other sizes are available upon request – enquire.

Genuine Products – Manufactured by Schmidt® / Axxiom Manufacturing

AVAILABLE FOR RENTAL OR PURCHASE

ABRASIVE RECOVERY VACUUM SYSTEM

• Will vacuum up to 8 ton/hour of garnet
• Requires 900cfm of air at 120 psi to operate
• Skid mounted abrasive recovery system, Pneumatically operated
• 4 Dust Collector Cartridges with filtration area of 904 sq ft.
• Automatic Reverse Pulse Cleaning
• Works best for dry media disposal

Our latest generation Mega MistBlaster offers both wet and dry blasting for the ultimate in flexibility!  It reduces costs and time when doing large projects and offers the following:

• Versatility.  4 functions available at the flip of a switch:
  • MistBlasting / Wet (slurry) Blasting
  • Traditional Dry Blasting
  • Wash-down mode
  • Blow-off mode
  • Each outlet is independently controlled, giving even greater versatility.
• Capability.  With its 4 outlets, this workhorse can power up to 4 operators OR a VertiDrive robotic blaster and manual blasting simultaneously.
• Huge capacity – As typically configured with 160 cubic feet (aka 8 Ton), this bulk pot holds half a truckload of garnet.
• Mount Options as follows:
  • Highway Trailer
  • Skid Mount
  • Shipping Legs (for mounting on your own equipment)
• Available Cost Saving Option – We can convert your existing Schmidt® Dry bulk pot with to our Mega MistBlaster with our retrofit package. Available as a Limited version (without metering / air valves, for new pots) or as a Full version (with all valves, for used pots).

More options and features shown under the description tab. Available for Purchase or Rental. Ask about a demo! Note: Designed for use with a 1600 CFM dryer, available here.

• Will transform your blast pot into a pressure hold system
• Retrofit Kit includes:
  • Thompson® Valve Series II Metering Valve
  • Full pusherline kit
  • Automatic air valve and all interconnecting hoses
  • Control line strainer and control valve
  • Response deadman handle and Twinline
  • Does not include muffler or pressure relief valve pictured
• Genuine Parts – Manufactured by Schmidt® / Axxiom Manufacturing

FREE Shipping

30 Day Money-Back Guarantee | Free Returns

90 Day Manufacturer Warranty

• Unique!  Dual Outlet for 2 operators, in a short configuration for easy loading.
• Only 46 inches tall!  Shorter than a standard 6.5 pot.
• Capacity of 11 cu ft, which equates to 1600lbs of a dense media like premium GMA Garnet
• Pressure Rating: 150psi
• TeraValve pressure-hold metering valves

Sold as a Kit which Includes:

• Blast Pot
• Pneumatic Deadman Control System comes with 2 sets of 50 feet of control line and handle
• Choice of inlet fitting in either 4-claw or Spud type. Spud will be supplied unless otherwise noted in Order Comments field.

BLAST HOSE sold separately

Genuine Product – Manufactured by Schmidt® /Axxiom Manufacturing

The Sponge-Jet B-Vac Pro is a premium system that integrates the 3 essential processes of sponge blasting into a single unit.  It is designed to reduce space requirements and deployment time, and is the most popular Sponge-Jet integrated system.  Due to it’s built-in vacuum system, it reduces the personnel need by 1 person, which makes it price-competitive on jobs of 4+ days duration.  Available for purchase or rent.

Selected features include:

• Feed Unit.  Large capacity pneumatic 470-SJ model with up to 2 hours blasting time.
• Recycler.  Pneumatic 50-P recycler with up-sized screen for faster processing.
• Vacuum.  With 11 inches of mercury, this powerful vacuum will transport up to 18 lbs of media per minute.
• Lifting frame.  Rugged design allows this 6500 lb unit to be transported by forklift or crane.  Built in ladder included.
• Other features.  Includes pressure relief valve, high-capacity muffler, secondary moisture separator, and more.
• Selected Options.
  • 55-gallon drop-out drum, which when positioned in-line with the vacuum system, reduces the dust loading on the vacuum filter.
  • Stand-alone moisture separator. Excellent for use when the primary air dryer is at a distance from the blasting unit.

Note:  Due to our distribution agreement with Sponge-Jet, pricing is not shown on our website.  Contact us for fast, competitive pricing or send in the web-form quote request.

• Permanent or temporary mounting systems
• Ideal for setting up temporary blasting/painting facilities
• Supplied in modular kit for simple, quick installation (under a week)
• Fully relocatable — easy to install and dismantle
• 100% Waterproof design
• Wind rating as per local requirements
• No concrete foundation necessary
• Compatible with optional abrasive recovery and dust collection equipment

• #1 Fastest Suction Blast System Available
• Uses an Abrasive Pick-Up Tube and flexible Hose to mix abrasive with the airstream
• To set up, simply slide the pick up tube into your bag of abrasive, connect your compressed air and pull the trigger
• Comes with a fixed orifice ¼’ Airjet and ½’ Tungsten Carbide nozzle
• Can be used with any media, right out of the bag
• Ideal for where air supply is limited or for small jobs where setting up conventional pressure blast machine is a nuisance
• Uses between 40-120 cfm of air – the more you have, the faster you blast.
• Sold as a Kit including the gun, nozzle and pick up tubes
• Also referred to as a bag blaster
• Genuine Product – Manufactured by Clemco

The Auto Air Valve (aka Gatekeeper) is the recommended control valve for a pressure-hold blasting system.  It is safer and superior to a pinch valve system.  Further details as follows:

• Rugged, compact design
• Typically used in conjunction with the Thompson Valve
• Low pressure drop across valve – increases production
• Multiple sizes available.
• Retrofit systems are available to convert pinch valve / donut valve systems to safer and more efficient Auto Air valve systems – see options below.

• Pressure-release deadman control valve i.e., blast machine depressurizes when the deadman handle is released.
• Used when an overhead hopper automatically feeds abrasive into a blast machine.
• Rugged stainless steel body, compact, isolated 2-bolt construction.
• Doubles blast machine refill cycle time.
• Virtual Position Indicator illustrates orifice size, giving the ability to set abrasive flow quickly and consistently.
• Set and forget – flow rates stay set where you put them.
• High wear, rugged plunger seal.
• Stainless steel body for long life.
• Improved urethane clean-out port enabling quick removal of obstructions while improving port and valve life.
• Fit a rebuild kit while the valve is still fitted to the blast machine.
• Sold individually.
• Genuine Products – Manufactured by Schmidt / Axxiom Manufacturing

Built by Schmidt®, these moisture separators are available in multiple versions as follows:

• Size
  • 800 or 1600 CFM capacity
• Configuration
  • Stationary or Portable (with handle, axle  & wheels)
• Fittings
  • Built with 2″ NPT ports on both Inlet and Outlet, these can be equipped with your choice of Spud or 4-claw fittings, ball valves, splitters, etc.

Note:  Fittings are optional and must be ordered separately.  See You May Also Like below.

FOR RENTAL OR PURCHASE

The Schmidt Bulk AmphiBlast™ combines the features of a MegaBlaster and dustless vapour abrasive blasting, and is the latest in technology and efficiency. The Bulk AmphiBlast™ has a super large capacity that allows up to 4 blasters to blast for up to 8 hours each without stopping to refill the blast pot.  Furthermore, each blaster can choose independently if they want to dry blast, mist blast (slurry), Softwash^TM or blow down.

FREE Shipping

30 Day Money-Back Guarantee | Free Returns

90 Manufacturer Warranty

• 10 cu ft Schmidt® Blast pot
• Excellent for a blastroom application with 1-2 blasters
• Single outlet Thompson® Valve II abrasive metering valve, Dual available
• Abrasive capacity
  • Garnet 1500 lbs
  • Steel Grit 2450 lbs
• Comes with pneumatic deadman handle and 55ft of control hose, Electric available

Genuine Products – Manufactured by Schmidt® / Axxiom Manufacturing to BlastOne specifications

Sponge-Jet blast media is unique in the field of abrasive blasting. (See How it Works under the Description tab.)

Depending on project requirements, many versions are available as follows (all versions use original sponge carrier unless noted):

• Silver Sponge series.  Incorporates aluminum oxide abrasive.
  • 16 to 320 mesh available, with the most common coating removal versions being Silver 30 or Silver 60.
  • A DG (Double Grind) version is offered in the 30 and 60 mesh.  This version is pre-processed to function like a working blend immediately, with up to 75% faster blast speed initially compared to original sponge abrasive.
• Red Sponge Media.  Incorporates steel grit abrasive.
  • Highly aggressive and typically used to remove pack rust and/or pitting.
• White Plastic Sponge Media.  Incorporates Type II 30/40 mesh plastic urea.
  • Lightly aggressive and used for coating removal without etching / profiling on steel or aluminum.
• White SPOCC Sponge Media.  Incorporates Spherical Precipitate of Calcium Carbonate.
  • Lightly aggressive and used for contaminant removal.
• White Glass Bead Sponge Media.  Incorporates 60/80 mesh glass bead.
  • Lightly aggressive, used for soft alloy substrates where a low-build coating system will be used.
• Green Sponge Media.  Incorporates Wollastinite cleaning agent.
  • Lightly aggressive, used for contaminant removal where moisture is not present.
• HyperX Media.  Proprietary blend of aluminum oxide and other medias.
  • Available in Medium or Coarse for 2 or 3 mil profile.
  • Uses a higher ratio of abrasive-to-sponge, for faster production than even the Double Grind.
  • Lower in cost, but not as effective in dust capture and with some ricochet, this media is best suited inside tanks or pipelines where 100% containment is assured.
  • Hyper X media requires a specific 3-screen setup using the 70 series recycler (#3, #16, and #50)
• Super Media-1. Incorporates a blend of steel & ceramic abrasives.
  • Highly aggressive, used for concrete blasting to expose aggregate, rubber lining removal on steel, lead paint removal in a demolition project, etc.
  • When blasting on steel, this product creates such a high profile (8 mil plus) that some of the sponge will embed.  If recoating, an additional cleaning process will be required using a steel brush, Bristle Blaster, etc.

All sponge media is packed 55 bags per pallet, with price breaks available at 1 pallet and at 6 pallets+.

Note:  Due to our distribution agreement with Sponge-Jet, pricing is not shown on our website.  Contact us for fast, competitive pricing or send in the web-form quote request.

• Dual Wheeled Trailer Mounted Blasting Package Including
  • BMS6.5 blast machine with Thompson® Valve outlet
  • 400 cfm AirPrep™ Air Dryer
  • 375 cfm 150 psi diesel air compressor
  • Breathing air filter
  • Carbon monoxide alarm
  • Tool box
  • Hose rack
  • Room for 1 skid of abrasive

• Service Kit for the 1-¼ (32mm) and 1-½ (38mm) Auto Air Valve
• Used to rebuild the Auto Air Valve in the field
• Includes Gaskets, Diaphragm, Brass Washers, Breather vent and required lubricants
• Replace seals at the first sign of wear

• TeraValve™ Complete Blast Pot Retrofit Kit
• Allows you to completely retrofit your existing blast pot into the latest pressure-hold technology
• Reduces abrasive consumption up to 15% compared to pressure-release systems, depending on application.
• TeraValve™ is designed to last with stainless alloy construction and internal dust wipers
• Sold as a kit with all parts, fittings and instructions required for installation
• Genuine Products – Manufactured by Schmidt® / Axxiom Manufacturing
• Kit pictured is 1-1/2″ Airlines, Electric Deadman – most common

BlastOne has the repair parts for your blasting equipment. This is the bracket to attach control valves / solenoids to standard Schmidt blast pots.

From gaskets and crabs to covers and bolts, BlastOne has all the replacement parts you need to repair the Handhole / Manway access panels for Axxiom / Schmidt blast pots.

• Special note:  Be sure to try out the SureFit™ Handway gasket for the 6.5 pot.  It makes installation much easier & faster.  Lasts longer too!
• Note:  Versions of these access assemblies have changed over the years.  If any doubt which version you need, send us the model year and serial number of your blast pot to confirm the correct part before ordering.

• Suits Schmidt 3.5 Blast Pot and MistBlaster Secondary Wheel
• 10″ Wheel & Tire
• Never Flat, rubber filled tires
• Makes for easy portability onsite
• Sold Individually
• Genuine Parts – Manufactured by Axxiom Manufacturing/Schmidt

$9,550
HIRE165

Interested in this product?
CALL 1-800-999-1881 or Email

*Do NOT add to cart or quote! Contact Us Directly for more information.

Updated and enhanced! BlastOne has refreshed its highly successful MistBlaster® and has released the latest generation with even more capability!

What HAS NOT changed:

• Industry-Leading Flexibility. 
  • The MistBlaster® is a true dry blaster with the added capability of being the best wet blaster on the market. It is not a limited-purpose dustless / slurry blaster that will sit around gathering dust most days.
• Water and Abrasive flow is separately adjustable. Maximizes production while keeping cleanup to a minimum.
• Reliable design.  Uses the latest generation TeraValve® metering valve on the popular 6.5CF pot chassis.
• Abrasive choice.  Will work with most abrasives in dry mode. In wet mode, garnet or crushed glass are recommended.

What HAS changed:

• Enhanced functionality. 4 functions are built into the control panel (Dry Blast, Wet Blast, Wash Down, and now Blow Down)
• Controls flexibility.  The dual deadman control system is now set up to operate either electrically or pneumatically.
• High-Flow piping.  Air pressure regulator has been deleted and piping has been upgraded to increase nozzle pressure.

All 6.5 c.f. MistBlasters include the following as standard:

• Single outlet TeraValve® abrasive metering valve
• Dual electric / pneumatic controls, including deadman handle and control line
• Industrial-strength Schmidt® VBS II Muffler

Configuration Options:

• Wheel version – Stand-alone unit, portable configuration
• Skid version – Stand-alone unit, mounted on a steel skid.
• Combo Skid versions, save setup time and storage space. Available in the following configurations:
  • Combo Skid 400 cfm Dryer Options as follows: 
    • Deliquescent type (4-season / highest efficiency)
    • Aftercooler Squat type (3-season / less effective in cooler temperatures)
    • No Dryer
    • Note: Unlike dedicated slurry-type blasters, the MistBlaster is designed around a standard dry vessel.  A stand-alone air dryer is required in order to realize a full return on your investment.
  • Combo Skid Mounting Options as follows: 
    • Steel Skid
    • Steel Skid with Frame
  • Combo Skid Breathing Air Packages as follows: 
    • With Breathing Air Station (breathing air filter, carbon monoxide alarm, and 50′ breathing air line)
    • Without Breathing Air Station
  • Note:  All Combo Skid configurations include an Air Manifold with spare air ports and a 50-gallon tank.
• Retrofit version:  Save money by retrofitting your existing 6.5 pot (must be structurally sound).  Available in wheel or skid configurations and includes all standard MistBlaster features.

Available for Purchase or Rental. Ask about a demo!

Additional details shown under the description tab.

The Axxiom ShortStop prevents accidental activation of electric deadman systems caused by short-circuits in the control cable.  This safety-enhancing option is especially beneficial when blasting at heights, or in applications where the control cable is susceptible to high wear.

The ShortStop PnP (Plug-n-play) is simple to install and includes the control module and junction box needed to convert existing electric control systems*. Both single-outlet and 4-outlet bulk pot conversions are available.

*Note:  Deadman handles are unique to the ShortStop PnP. Conversion kits do not include handles, which are available separately on this page.

• Deadman-operated control valve (solenoid)
• Uses an electric or pneumatic charge to push over the shuttle which opens ports to control the deadman system
  • Provides sharp, clean and rapid response
  • Improves safety
• Installs between twinline and inlet valve
• Reduces wear on both the remote control exhaust valve and the abrasive metering valve

• 2-claw threaded coupling for metering valve outlet, to enable connection of blast hose
• Supplied with HFGMRLP coupling gasket fitted
• For Aluminum, Brass, and Steel,  use HFCLP1 thin safety lock pins – purchase separately
• Nylon is supplied with HFGPCG gasket fitted and contains an integral springlock pin
• 2 types available – Standard and MegaMax.
  • Note: MegaMax and Standard couplings require an adapter to fit together.
• MegaMax couplings are Full-Flow, designed to remove the air restrictions caused by standard couplings, and increases the PSI available to the nozzle.  The increased PSI is mostly beneficial when doing high-production blasting using 1.5″ or 2″ ID Blast Hoses.
• These are threaded couplings designed for metering valve outlets only.  Unthreaded QC couplings are used on blast hoses, and can be found HERE.
• Note:  1 1/4″ threaded couplings can also be used as Quick-couple type nozzle holders for fine thread nozzles.
• Industry Size Commonly Referred to as SB1, SB-1, SB2, SB-2

• Tri-Clover Connector with Built in Ball-Valve
• Locate between the metering valve and the bottom of the pot to reduce maintenance time on the metering valve.
• Combines 2 time savers:
  • Tri-Clover connection allows for easy removal of metering valve.
  • Ball valve allows for removal of metering valve without emptying the pot.
• 1 1/4″ x 1 1/4″ NPT Threads – suits most blast pots and abrasive metering valves
• Use thread sealant tape or compound to ensure an airtight connection
• NOTE – this option adds 6 inches in height. Ensure that your pot has the required clearance before ordering, or that you can add the needed height to your existing pot.

The Thompson I Valve was invented by Bob Schmidt and was instrumental in causing the popularity of pressure hold technology.

• Pressure-hold systems retain the pressure in the blast pot until the deadman handle is depressed.  This reduces abrasive and energy waste.
• The Thompson I offers fine control for abrasive metering
• It comes in 3 nipple size configurations:
  • 1 ¼” (32 mm) x 1 ¼” (32 mm)
  • 1 ½” (38 mm) x 1 ½” (38 mm)
  • 2″ (50 mm) x 2″ (50 mm)
• Threaded-plunger metering design with air actuated operation
• Fits most sand blast hoppers, blast pots or abrasive blasting machines
• Genuine Parts – Manufactured by Schmidt® / Axxiom Manufacturing

Note:  The Thompson I valve, while still available, has become less common. The more modern Thompson II valve or state-of-the-art TeraValve are more popular and can replace the Thompson I without any modifications.

The Axxiom TeraValve – the next generation abrasive metering valve for blast machines with pressure-hold technology.  Featuring:

• Extended Life.  Schmidt XL technology utilizes tough metal alloys and internal wipers, reducing premature wear due to dust migration.
• Easy Interchangeability.  Customers with older Thompson valves that need rebuilt have an easy alternative.  Exchange the old valve with a new TeraValve with no modifications required!
• Efficient.  Pressure-hold design maintains pressure in the pot, even with deadman released.  This can save up to 15% of abrasive when your projects involve a lot of start-stop blasting.  Reduces expensive compressed air consumption too!
• Economical.  The compact design of the TeraValve actually costs less than the previous-gen Thompson II valve.
• Available for more applications.  Pressure-release pots with limited clearance (where traditional Thompson Valves do not fit) can also benefit. Efficient pressure-hold technology can be used on any blast pot with a minimum of 6″ clearance by installing a TeraValve retrofit kit.
• Genuine Parts – Manufactured by Schmidt® / Axxiom Manufacturing

Note:  Diaphragm-activated piston requires minimum of 75 psi control pressure

• Suits 24″ large blast pot
• Pop-Up Umbrella Spider Plate allows valve to pop-up easily when a head of abrasive is stored above the blast machine
• Installed into the pot of the blast pot
• Used in auto-loading applications such as blastrooms, recovery systems etc.
• Sold as a complete assembly including the legs and arms

• Keeps Abrasive grit and dust out of the controls of your blast pot
• Helps maintain valve response and speed
• Extends valve seal life
• Must have essential for any blast pot.
• Easy to maintain and clean
• Uses a 90 micron bronze element
• 1/4″ inlet fittings

• Heavy duty long life pot connector to prevent the top thread of the MicroValve from wearing
• 1 ¼” (31.75 mm) threads both ends

• 1-1/4″ x 1-1/4″ FNPT Threads, with half-round handle – fits most blast pots
• Incorporates ball valve and union connection
• Reduces maintenance time – allows the metering valve to be removed without emptying the pot
• Can be used independently, or in conjunction with a Tri-Clover Quick connector. To order this combination as a unit, use part number GV2410320SPBV (saves cost).
• Use thread sealant tape or compound to ensure an airtight connection
• NOTE – this option adds about 3 inches to the height of the valve – ensure that you have sufficient clearance before ordering.

Sized between the Tite Space and the full size nozzles, the ATA series of angle nozzles come standard with ¾” Medium Threads. They are excellent for applications requiring the operator to operate in small areas, especially when paired with a small bore whip-hose. Basic specs are:

• 3/4″ (20mm) Medium male thread (other options available by special order).  Can be used in standard Fine or Coarse nozzle holders by use of a thread adapter available here.
• 1/2″ (13mm) throat entry
• 45° forward, 90° right angle, and 135° reverse blast pattern options available
• Some sizes are available in Double, Triple or Quad orifices
  • Note:  Using nozzles with multiple orifices will multiply the compressed air CFM requirement accordingly
• Tungsten carbide liner.  Extended life liners for large projects available by special order.
• Short 2-1/8″ length

Contact us for additional options available by special order.

• Hi-flow Blast Pot Pusherline Kit
• Used on Blast Pots between the air control valves and the metering valve
• Sold as a complete assembly Including
  • Pusherline Air Hose
  • 1-¼” ball valve
  • 1-¼” Nut and tails with bolt style clamps for in-field installation
  • Does not include Metering Valve

• Steel Grit Trailers are highly transportable and commonly used for bridge blasting and water tank painting contractors.
• The system incorporates a powerful diesel powered vacuum system, interceptor cyclone system, abrasive classifier, storage hopper and blast machines.
• Different size systems are available ranging from 2 blast pots to 8 blast pot systems and is mounted on a low deck 53 foot trailer.
• Up to 12 ton/hour of steel grit

• Installed in the riser tube below the pop up valve of the blast pot
• Used to stop backflow of air into the control lines and valves
• Typically used when blasting with fine or dusty abrasives
• Suits 1″ riser tubes
• User will need to reduce current riser tube height to make this fit.
• Allows maximum pressure fluctuation without back flow of dust and abrasive.
• Sold individually
• Genuine Parts – Manufactured by Axxiom Manufacturing/Schmidt

BlastOne has the parts to maintain your Clemco® blast equipment. This is the rebuild kit for 1″ abrasive trap on the RMC valve (factory part number 01925). Includes the following:

• DMRMCATCS Abrasive Trap Screen (3)
• BA02013 O-Ring (2)
• Clean Screen Decal (Not available separately)
• DMRMCATCSG Gasket

NOTE: BlastOne also has retrofit kids with upgraded valves, and which are designed to reduce maintenance while keeping your current pot. For pressure hold retrofit kits, see here. For pressure-release retrofit kits, see here.

When Axxiom released the Thompson 2 valve, the benefits of Pressure-Hold technology were instantly upgraded by improved user experience over the Thompson I valve.  Details as follows:

• Improved servicability:
  • Body and cylinder are now 2 parts, providing easier removal of sleeve and plunger.
• Additional Seal protection:
  • Has 3 separate seals (versus the original 1), reducing dust migration and improving durability.
• Multiple Sleeve choices:
  • In addition to the original Tungsten Carbide and Urethane full-flow options, Axxiom has released additional options that help prevent over-consumption in various applications.
• Virtual Position Indicator:
  • Simplifies setting of the media flow rate.
• Cleanout:
  • Full 1″ port directly under the inlet allows cleanout without removing the valve.
• Size info:
  • Standard 1-¼” (32 mm) inlet thread
  • 4 choices of MNPT piping for pusher-line connection
    • 1″, 1-¼”, 1-½”, and 2″
• Options:  Make servicing the valve even more convenient with one of the following:
  • Union-End Ball Valve – The UEBV allows removal of valve without emptying the pot.
  • Tri-Clover Quick Connect – allows removal of valve without tools.
  • Combination UEBV and Tri-Clover – combines the benefits of both options at a reduced cost.

Meter your abrasive efficiently and conveniently with the genuine Axxiom Thompson II valve!

AVAILABLE FOR RENTAL OR PURCHASE

• Capacity of 4 tons of garnet
• Designed to sit between the VacuLoad and the vacuum head
• Separates abrasive and 90% of dust for reuse or disposal
• Available in 3 sizes – 20, 55, and 100 cu.ft
• Acts as a cyclone separator using power from the main vacuum unit
• No need for compressed air or electric power
• Ideal for abrasive storage

AVAILABLE FOR RENTAL OR PURCHASE

• • FREE Shipping
  • 30 Day Money-Back Guarantee | Free Returns
  • Will vacuum upto 2 ton/hour
  • Requires 350 cfm compressed air at 120 psi
  • 1 Dust Collector Cartridge with filtration area of 229 sq ft.
  • Automatic Reverse Pulse Cleaning
  • Use with 3″ vacuum hose

• Suit Schmidt Blast Pots
• Warning Decal Kit for small blast pots 0.9-10cuft
• Includes all warning labels
• Ensure your equipment has the legal liability notices clearly present

• Industrial-Grade Muffler for Manual Blow-Down (Pressure-hold) Blast Pots with Thompson valve or TeraValve
• Safer and much longer lasting than ‘throw-away’ mufflers
• Reduces blow-down noise to approximately 110 dB
• Intercepts abrasive that may otherwise escape when depressurizing
• Sold as a Field-Installable Retrofit Kit including;
  • VBS II Exhaust Muffler
  • Mounting Bracket (Goes on blast pot leg)
  • Blowdown Hose Assembly
  • Ball Valve and required fittings
• Genuine Products – Manufactured by Axxiom Manufacturing/Schmidt
• Also available for Pressure-Release pots here

FREE Shipping

30 Day Money-Back Guarantee | Free Returns

90 Day Manufacturer Warranty

• The most versatile, easy-to-regulate dry blast machine on the market
• 10-150psi blasting pressure range
• With a load skid combined with an inlet filter, this product uses a differential pressure gauge to allow accurate “metering” of hard-to-flow abrasives like Soda and fine Garnets
• With regulators for the blast and tank pressure for accurate control, this product can be used with most abrasive types – fine to coarse
• With the addition of a media vibrator to improve light media flow and an easy-to-use media shut-off valve this unit is perfect for graffiti removal and all other types of soda blasting
• G2 pneumatic deadman control, 55′ twinline control hose, 55′ water line with wet blast attachment for dust suppression included with purchase

Genuine Products – Manufactured by Schmidt® / Axxiom Manufacturing

• 3/4″ NPSM (20mm) ‘M’ Medium thread
• 1/2″ (13mm) throat entry
• Tungsten carbide liner
• Aluminum jacket and thread
• Very short – 1-5/8″ long
• Commonly used with Internal Pipe RotorBlast when blasting pipes between 8 and 11 inches in diameter, or in other hard-to-reach blasting areas
• Uses HFGFBSP nozzle washers (not included) – order separately

• O-Ring Seal for 10” Schmidt blast pot closure 7mm section
• Used to create a complete seal on the top of the megablaster
• Recommend you replace seal at first sign of wear
• Sold Individually
• Genuine Parts – Manufactured by Schmidt / Axxiom Manufacturing

• Industrial-Grade Muffler for Pressure-Release Blast Pots
• Safer and much longer lasting than ‘throw-away’ mufflers
• Reduces blow-down noise to approx. 110 dB.
• Intercepts abrasive that may otherwise escape when depressurizing
• Sold as a Field-Installable Retrofit Kit including;
  • VBS II Exhaust Muffler
  • Mounting Bracket (Attaches to Combo Valve)
  • Any required fittings
  • Does not include a new Blow Down hose
• Genuine Products – Manufactured by Axxiom Manufacturing/Schmidt
• Note:  This muffler comes standard on Schmidt combo-micro blast pots from BlastOne.
• Also available for Pressure-Hold systems here

• Thompson Metering Valve II lasts up to 10 times longer than any other valve, due to its unique engineering
• Designed to handle the harshest blasting environments known
• Will handle up to a 3/4″ blast nozzle
• Will work with any abrasive, including very fine/dusty abrasives
• Most rugged and reliable valve for any application
• Sold Individually
• Genuine Parts – Made in USA by Schmidt / Axxiom Manufacturing

Schmidt changed the abrasive blasting industry when they introduced the MicroValve™.  Now known as the MicroValve I (or the Original Microvalve), it is still available although most pressure-release Schmidt pots now use the newer MicroValve III®.

It features:

• Simple threaded screw-type metering
• Hardened steel threaded base nipple
• (The brass threaded coupling shown is available separately.)
• Genuine Products – Manufactured by Schmidt® / Axxiom Manufacturing

• OEM Urethane Seat suit Thompson Valve 2
• Used with the Tungsten Carbide Sleeve (The most common)
• One of the main signs of wear is air leaking out of the nozzle when you’re not blasting but the pot is pressurized
• Schmidt / Axxiom part # 2152-000-10

BALL AND CHAIN SOLD SEPARATELY

• Increases productivity and reduces costs
• Permanently sealed pneumatic switch is protected by abrasion-resistant urethane

• Piston-operated valve
• 1/4″ female NPT supply air connection
• Effortless activation via deadman control handle
• Guide tubes ensure consistent plunger travel
• Eliminate repressurization down time profit loss

AVAILABLE FOR RENTAL OR PURCHASE

The “Twin line Deadman Control Hose” (SKU: AHRMS4055) offers a safe, heavy-duty solution for pneumatic deadman controls. Bonded and color-coded for enhanced safety, it is available for rental or purchase.

• Bonded, heavy duty, twin rubber hose, color coded for safety
• Used to supply air to the deadman handle which is used to signal a “blast” return charge of air to the blast pot control valves
• Always replace the hose at the first sign of wear, this is a safety deadman control item.
• Fitted standard with male-female threaded connectors
• 1/4″ (6 mm) connectors on ‘supply’ red hose
• 1/8″ (3 mm) connectors on ‘return’ green hose
• 55 ft length
• Please Request Rental Pricing

When the primary air dryer is located at a distance from the blast pot, secondary moisture removal becomes critical.  The Sponge-Jet moisture separation tank is ideal for this application.  Includes the following:

• Handle for easy portability
• Spud / BOSS blast hose fitting
• Multiple sized ball valves & couplings

Note:  Customization is available if specific sizes are needed.

Due to our distribution agreement with Sponge-Jet, pricing is not shown on our website.  Contact us for fast, competitive pricing or send in the web form quote request.

The Rubber-Lined Hex 1-1/4″ Pipe Nipple is an essential component designed for seamless connection between the flat sand valve and the blast pot in sandblasting equipment. Engineered for durability, it features a rubber lining to withstand the rigors of use, ensuring an extended service life.

• Optimal fit for flat sand valves.
• 1-1/4″ ID hex design for easy installation and secure connection.
• Enhanced durability with rubber lining for prolonged lifespan.
• Perfect for professional sandblasting setups in both B2B and B2C markets.

• Suits AHR general purpose air hose
• Two piece fitting, hose tail to swivel nut female thread
• Various clamping options – double bolt clamp or bandit clamp
• Sold individually

BlastOne has the parts needed to service and maintain all Axxiom / Schmidt blast pots.  The following are the common Pop Up components – contact us if you do not see the version you need.

Pop-up Valve and Shaft (aka Pop-up Head)

• Hemispherical pop-up valve seals off pot when pressurized
• Shaft is embedded in the urethane head
• Suits Schmidt’s contractor series blast pots
• Available in the following:
  • MPN 2100-000, Small, for 1.5 CF pots
  • MPN 2100-010, Standard, for 3.5, 6.5, 10, & 20CF pots
  • MPN 2100-010-04, Alternate for Standard sizes, designed for high flow

Seating Ring

• Available in the following:
  • MPN 2100-001, Small, for 1.5 CF pots
  • MPN 2100-011, Standard, for 3.5, 6.5, 10 & 20 CF pots
  • MPN 2100-011-04, “Sure-Seal” Alternate for standard sizes, good when applications include blasting at low pressures.  Use with 2100-010-04 pop-up head.

• ASAP Safety System Retrofit Kit for 12V DC Thompson® Valve system.
• This System changes the depressurization flow of the air in the blast hose
• Allows a 200ft blast hose to depressurize in less than 1 second
• Changes the depressurization flow to exit backwards through full porting vs having to exit out of the blast nozzle
• Saves Seconds – Saves Lives, if a blaster drops a hose every micro-second counts, it takes the energy out of the hose immediately.
• Sold as a complete kit to be added on to an Electric Controlled Thompson® Valve Blast Pot
• Genuine Products – Manufactured by Schmidt® / Axxiom Manufacturing

• Suits most blast pots and valves (any with 1-1/4″ NPT Thread)
• Locate between the metering valve and the bottom of the pot to reduce maintenance time on the metering valve.
• Allows easy removal of metering valve from pot
• Can be used independently, or in conjunction with a Union End Ball valve.  To order this combination as a unit, use part number GV2410320SPBV (saves cost).

• 1-1/4″ Heavy Duty Media Inlet Nipple with increased abrasion resistance
• Connects Metering Valve to Blast Pot
• Suits all Schmidt Abrasive Blast Pots, and any other vessel with a 1 1/4″ NPT Metering Valve Ports

• Suits Blast Pot timer
• Pressure Switch to allow hour counter to count actual blasting hours
• Working PSI range of 10-150 PSI
• Sold Individually

• 3-pin Quick connector
• ‘TwistLok’ action designed to prevent cables from accidentally disconnecting
• Panel mount available DM ECK100
• 3-Pin / 3-Prong Twistlok are most commonly used for deadman cable
• 2-Pin / 3-Prong Twistlok commonly used for Electric Power Supply
• Sold Individually

Technology insertion to exponentially increase shipyard blast and coat production.

COMPONENTS & FEATURES

The individual technologies include, but are not limited to:

• Intelliblast Blast Pot Controls:
  • Smart controls that optimize blasting parameters for maximum efficiency and effectiveness.
• Snakebite Blasting Nozzles
  • High-performance nozzles designed for precise and powerful material removal, reducing blasting time and lowering process noise.
• Rapidly Deployable Containments
  • Innovative containment systems that can be quickly deployed, ensuring a controlled environment, and minimizing the spread of contaminants.
• Vortex Airflow Movement
  • Proprietary airflow design that lowers energy consumption, enhances ventilation, and ensures the efficient removal of particles from the blasting and painting areas.
• Combination Dual Air Plenums
  • Dual air plenums that provide a uniform and controlled airflow, optimizing the blasting and painting processes.
• Energy Recovery System (ERS)
  • An energy recovery system that captures and recycles heat energy, reducing overall energy consumption and operational costs
• Robot Ready Design
  • A structure and system that is designed to be capable of supporting automated process equipment

BENEFITS 

• Faster production cycles
• Reduced operational costs
• Enhanced environmental sustainability
• Improved worker safety

Elevate your sandblasting assembly with the 1-1/4″ Rubber-Lined Wye, expertly designed to connect the flat sand valve to the pusher line, blast hose line, and blast pot nipple. This Y-piece pipe fitting is engineered with 1-1/4” x 1-1/4” x 1-1/4” standard NPT female threads and features a durable rubber-lined steel construction for an extended wear life.

• Ensures seamless integration with your sandblasting system.
• Durable rubber-lined steel construction for maximum longevity.
• Standard 1-1/4” NPT female threads for universal compatibility.
• Direct replacement for OEM parts: Clemco 01818 and Axxiom 3012-107.

• To replace the valves on your pressure release blast pot
• Retrofit Kit includes:
  • 1 1/4″ Combo Valve
  • 1 1/4″ MicroValve 3
  • Full pusherline kit
  • All interconnecting hoses
  • Control line strainer and control valve
  • Response deadman handle and Deadman line

• Suits Combo Valve Blast Machines
• Blow down hose is used as part of the blast pot exhaust valve
• When the deadman is triggered, the combo valve pinches off the blow down hose, and lets the pot pressurize
• Includes 3′ of high-quality 3/4″ 4-ply blast hose
• Comes fitted with a 1-1/4″ threaded blast hose fitting to allow attachment to the blast pot

• Suits most blast pots and valves (any with 1-1/4″ NPT thread)
• Locate between the metering valve and the bottom of the pot to reduce maintenance on the metering valve
• Allows easy removal of metering valve from pot
• Can be used independently, or in conjunction with a Union End Ball Valve.  To order this combination as a unit, use part number GV2410320SPBV (saves cost).
• Alternate version to Tri-clover assembly without spring-loaded hinge

Discover the convenience and performance of the “Twin-line Control Hose (3/16″) – Coupled” (SKU: AHRMS4050C). Expertly crafted to streamline your blasting operations:

• Directly pre-coupled with female swivel joiners for effortless setup
• Specific 3/16″ I.D., stretching 50′ in length, tailored for Clemco equipment compatibility
• Designed to bridge the deadman control trigger with the valves on your blast pot, ensuring a tight, efficient connection
• Features a distinct Yel/Yel coloring with a Black stripe for easy identification
• Experience superior coupling, specifically for Clemco equipment users

Choose the Twin-line Control Hose for reliability, ease of use, and optimal blast performance.

• Suits Electric Blast Pot Control Valve DM2229100
• Service Kit is used to keep your blast pot operational
• Sold as a Kit containing;
  • Piston
  • Spring
  • Replacement O-rings
  • Face Seal
• Genuine Parts – Manufactured by Schmidt / Axxiom Manufacturing

• Suits Blast Pot timer
• Suit No Voltage Applications
• Used to measure actual hours spent blasting
• LCD Timer with Built-In Battery
• Sold Individually

Heavy-duty pipe fitting connects flat sand valve to pusher line, blast hose line, and blast pot nipple.  Specifications:

• 150# malleable iron wye
• 1-¼” x 1-¼” x 1-¼” standard NPT female threads

This common wear item is also available with rubber lining to extend life – see You May Also Like below.

The Flat Sand Valve is legacy metering technology, where the metering is performed by sliding a lever to open and close the abrasive port.  It is simple in design and relatively inexpensive, but has a few limitations.  Details as follows:

• Slide-plate metering design, controlled by lever
• 1 1/4″ (32 mm) ports
• Features side cleanout-inspection port
• Available with or without outlet nipple and Y-piece (Optional rubber lined nipple is available to extend nipple life.)
• The major limitations are:
  • Not recommended for use with metallic abrasives
  • The slide plate/lever design does not provide effective fine metering control.  Typically this results in over consumption of media.  For low-volume blasting using inexpensive media, this may not be an issue.

Note:  These limitations can be eliminated by replacing the FSV with a MicroValve 3.  No modifications required.  Alternatively, legacy pots with inlet-outlet controls and FSV technology can be completely modernized with either the MicroValve Retrofit Kit (for pressure-release technology) or the TeraValve Retrofit Kit (for pressure-hold technology).

BlastOne has the parts to maintain your Clemco® blast equipment. This is the rebuild kit for the 1″ inlet valve (replaces factory part number 01929). Includes the following:

• BA01969 Plug Washers (2)
• BA01982 Compression Spring, small
• BA01986 Plug Washer Retainer
• BA01989 Bottom Cap Seal
• BA01990 O-Ring, Medium
• BA01992 O-Ring, Small

If you need the rebuild kit for the 1-½” inlet valve version, click here.

NOTE: BlastOne also has retrofit kits with upgraded valves, and which are designed to reduce maintenance while keeping your current pot. For pressure hold retrofits kits, see here. For pressure-release retrofit kits, see here.

• Suit Clemco Blast Pots
• Replacement pop-up valve with External Pop up sleeve
• Designed to go over the riser tube to help minimize backward flowing abrasive
• Also work when you have a low pressure and volume of air
• Only needed because Clemco inlet and outlet valves are slow to close
• Seating rings sold separately – BAP5

• 24 ft cable with alligator clips
• Connects directly to a battery to supply 12 volt power for deadman controls
• Deadman cable is fitted with a 2-Pin TwistLok plug connector for connecting to Deadman controls on the blast pot

• Multi-purpose relief valves
• Male threaded ports
• Use on Blast Pots, or other Pressure Vessels including Airpigs distribution manifold, Air Receivers, and AirPreps

BlastOne has the parts to maintain your Clemco® blast equipment. This is the rebuild kit for the piston outlet valve (factory part number 01928). Includes the following:

• BA01969 Plug Washers (2)
• BA01972 Valve Plug
• BA01974 Compression Spring
• BA01986 Plug Washer Retainer

NOTE: BlastOne also has retrofit kits with upgraded valves, and which are designed to reduce maintenance while keeping your current pot. For pressure hold retrofit kits, see here. For pressure-release retrofit kits, see here.

BlastOne has the parts to maintain your Clemco® blast equipment. This is the rebuild kit for the 1-½” inlet valve (replaces factory part number 01927). Includes the following:

• BA01982 Compression Spring, small
• BA01998 Plug Washers (2)
• BA02000 Compression Spring, large
• BA02002 Plug Washer Retainer
• BA02006 Bottom Cap Seal
• BA02007 O-Ring, large
• BA02008 O-Ring, small

If you need the rebuild kit for the 1″ inlet valve version, click here.

NOTE: BlastOne also has retrofit kits with upgraded valves, and which are designed to reduce maintenance while keeping your current pot. For pressure hold retrofit kits, see here. For pressure-release kits, see here.